Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Firewall Grommet
p/n: 30-0093-21
This Firewall Grommet is used to run the ignition advance along with various rods and tubing through the firewall. Designed from the original part for superior fit and seal.
Body Mounting Pad
p/n: 70-0265-48
This Body to Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs in metal bucket cups. Fully molded high quality EPDM rubber.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Engine Mount Pad
p/n: 11-0028-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Shock Absorber Bushing
p/n: 40-0273-32
Bushing. shock absorber link, smaller type. Eight (8) required per car. Compare with our #40-0069-32 (larger type). Length: .9375 inches.
Starter Button Cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Engine Mount Pad
p/n: 11-0029-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Engine Mount Pad
p/n: 11-0027-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.