Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Running Board To Body Filler
p/n: 70-1116-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a forty (40") inch pair of filler strips.
Rear Quarter Window Gasket Set
p/n: 60-0092-83
This rear corner quarter window gasket set contains the quarter window gaskets and locking strips. All of the strips in this four (4) piece set come in forty-five inch (45") pieces and mount around the perimeters of the quarter windows on five window trucks. The ends may require trimming and bonding for installation.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Headlight seal
p/n: 70-2574-14
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
Axle Rebound Pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Upper Control Arm Shaft
p/n: 20-1278-32
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Hood to Cowl Weatherstrip
p/n: 40-0470-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) foot long x 13/16” wide weatherstrip provides complete coverage.
Steering Column Floorplate Gasket
p/n: 60-0395-36
This Steering Column Floorplate Gasket is designed from the original part for superior fitment and seal. Cover (grommet), steering gear-to-toe board seal. Width: 5-13/16" inches. Height: 6" inches.
Front or Rear Door Seals
p/n: 60-0595-72
Door edge weatherstrip, front or rear door. This part is the primary door to body weatherstrip. Two strips fourteen (14') feet each. Glue in type. Used on the front doors for Buick, Oldsmobile & Pontiac models.
Window Felt Beltline Weatherstrips
p/n: 20-3066-60
This is a Standard material style Window Felt Beltline Weatherstrip pair (also known as beltline weatherstrip). The Left or Right door anti-rattler pair contains one (1) outer piece for door and one (1) inner piece for garnish molding. Includes clips installed and ends bent exactly as original.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Window Felt Beltline Weatherstrips - Right Quarter Window
p/n: 20-3072-60
This is a Right Side Quarter Window only Window Felt Beltline Weatherstrip pair. These anti-rattlers come ready to install with finished ends and body curvature bends for a factory like appearance. This one (1) pair of inner and outer right side window felts accomplishes one (1) side.
Window Felt Beltline Weatherstrips - Left Quarter Window
p/n: 20-3073-60
This is a Left Side Quarter Window only Window Felt Beltline Weatherstrip pair. These anti-rattlers come ready to install with finished ends and body curvature bends for a factory like appearance. This one (1) pair of inner and outer left side window felts accomplishes one (1) side.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Axle Bumpers
p/n: 60-0491-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming rebound pads are dense rubber blocks that mount to the rear axle tube.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Rigid Run Channel
p/n: 60-0073-58
Channel, rigid division bar. Un-beaded, cloth covered, mohair lined. Perfect replacement requires drilling for screws.