Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Fog Light Gasket
p/n: 70-0609-17
Gasket, fog light opening.Length: 12.25 inches. Width: 5.5 inches. Height: .50 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Backup light mounting pad
p/n: 70-0582-17
Pad, backup light mounting. Made with angled surface to align light with body.
Fog Light Gasket
p/n: 70-1243-17
Seal, fog light body. Without notches. For seal with notches see our #70-1242-17.Length: 6.5 inches. Width: 7.75 inches.
Fender Skirt Edge Weatherstrip
p/n: 70-0289-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Spring Shackle Bushing Set
p/n: 20-1581-33
This Spring Shackle Bushing Set is for the rear leaf springs. This set is an original steel stud type.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Transmission Mount Revulcanization Service Only
p/n: 10-0157-25
This Revulcanization Service is designed to restore your existing Transmission Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Convertible Top Arm Pad
p/n: 50-0310-67
Pad, folding post, lower, on bottom of post, held by two (2) screws. Brass core, right and left hand.