Rear Engine Mount
p/n: 20-0421-11
This Rear Engine Mount helps eliminate engine vibrations. Used as a rear engine support or transmission mount. Designed with rubber over a metal core.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Taillight Lens Gasket
p/n: 70-2140-15
Gasket, trunk center medallion trunk stop lamp lens. Proper construction with accurate lips for good sealing.Length: 1.375 inches. Width: 4.0625 inches.
Exterior Windshield Division Bar
p/n: 20-2341-51
This stainless steel Exterior Windshield Division Bar is designed from the original part for superior fitment, appearance and function.
Rear Window Gasket
p/n: 20-1668-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1660-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 20-0395-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Door Hinge Weatherstrips
p/n: 20-1643-73
This Door Hinge Weatherstrip pair is designed from the original parts for superior fitment and sealing. These door edge weatherstrips are molded specifically to fit the door hinge area of the vehicle.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Rear Gravel Deflector to Bumper Seal
p/n: 60-0020-30
This Rear Gravel Deflector to Bumper Seal is made of a high quality EPDM dense rubber extrusion. Designed from the original part so it fits correctly. Sold as a six (6) foot strip.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Front Fender Seals
p/n: 60-0522-45
Seal, front fender baffle, right and left. One (1) pair per car. Length: 5-1/4" inches.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.