Back Up Light To Body Gaskets
p/n: 20-2690-17
This Back Up Light To Body Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the backup light and the rear vehicle body.
Pickup tie down mounting pad
p/n: 20-0885-45
Pad, pickup box tie down hook. Eight (8) required per truck.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Front Fender or Quarter Panel Extensions
p/n: 20-2761-45
This Front Fender or Rear Quarter Panel Extension pair is designed from the original part for superior fitment and seal. The pair comes as one solid unit that is perforated for the customer to split apart and is easy to install.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Steering Column - Floor Seal
p/n: 70-3495-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Trunk Decklid Bumpers
p/n: 70-2044-87
This Trunk Decklid Bumper pair is designed from the original part for superior fitment, finish and function. These rubber bumpers attach to the trunk decklid to support / cushion lid closure.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Firewall Plug - Oval Rubber
p/n: 20-0754-20
This Firewall Plug is designed from the original part for superior fitment and finish. Usually requires three oval plugs per truck.
License Plate Light Lens Gasket
p/n: 70-3497-17
This License Plate Light Lens Gasket is designed from the original part for superior fitment and seal. This gasket fits between license plate light lens and housing.
Windshield Wiper Pivot Gaskets
p/n: 20-0891-53
This Windshield Wiper Pivot Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket is die cut from original style EPDM rubber for an authentic fitment, finish and function.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Hood Bumper
p/n: 70-0866-42
This Hood Bumper is a quality reproduction of the original factory part. The hood bumpers provide a cushion for the hood closure that also minimizes vibration.
Hood, Door Or Liftgate Bumpers
p/n: 20-0907-71
This Hood, Door Or Liftgate Bumper pair is a quality reproduction of the original factory part.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
PCV valve grommet
p/n: 20-2697-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Bumper Cap - Door, Hood and Trunk
p/n: 82-0020-42
This Bumper Cap is a quality reproduction of the original factory part. Serves as a Door, Hood and Trunk Bumper Cap for adjustment bolt. 7/8" diameter X 7/16" thick. Each
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Hood Bumper
p/n: 70-0991-42
Bumper, hood to fender ledge. Typically four (4) to six (6) used per car.Length: 1.15625 inches. Width: .3125 inches.
Hood to Fender Bumper
p/n: 70-1630-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) to six (6) required per vehicle.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Tailgate Bumper
p/n: 70-1609-87
This Tailgate Bumper is a quality reproduction of the original factory part. Made of a high-quality EPDM rubber, the bumper attaches to the vehicle body to support / cushion the tailgate closure.
5/16” Round Top Hood Bumper
p/n: 20-2755-42
This Hood Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the front radiator support to cushion / bump stop the hood closure.
2" Firewall Grommet
p/n: 60-0707-20
This Firewall Grommet is used to run the body wiring harness at the engine bulkhead through the firewall. Special design for this usage.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Door Bumper - Lower
p/n: 70-1605-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rear of door lower bumper attaches to the vehicle body to support / cushion the door closure.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Tailgate Bumper
p/n: 20-0888-45
These Tailgate Bumpers are designed from original parts for a correct fit. Sold as a pair.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Parking Brake Cable To Floor Seal
p/n: 20-0853-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment and seal. This works to seal the parking brake cable as it passes through the truck floor pan.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
AC Condenser Tube to Radiator Support Grommet
p/n: 20-2723-31
This A/C Condenser Tube to Radiator Support Grommet is used to protect the air conditioner condenser tubes to the radiator support. Made from flat foam rubber to provide protection.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1251-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. One fourth (1/4") of an inch high.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1252-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Five sixteenths (5/16") of an inch high.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1250-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Three sixteenths (3/16") of an inch high.
PCV valve grommet
p/n: 20-2696-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
Door Bumper
p/n: 70-1563-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure.
Door Glass Bumper
p/n: 20-1172-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.
Tailgate Side Seals
p/n: 70-4009-85
This Tailgate Side Seals includes right and left side with installation screws. These seals are properly molded from originals for a factory like fit.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Body Hole Plug
p/n: 20-0843-20
Plug, style-side bed side panel. One and five eighths (1-5/8) inch diameter. Fits 1-1/16" hole.
Body Hole Plug
p/n: 20-0845-20
Plug, oval floor pan front. Rubber. One half (1/2) inch by one (1) inch diameter. Two (2) each required per truck.
Body Hole Plug
p/n: 20-0844-20
Plug, cowl side panel inner. One and seven eighths (1-7/8) inch diameter. Two (2) each required per truck.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
1" Floor Pan Plug
p/n: 35-0262-20
This Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to twelve (12) used per vehicle.
Engine light grommet
p/n: 60-0706-17
Grommet, engine compartment light wire in lid. Not a universal grommet, this part is dimensionally just like the original.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
Window Regulator Arm Roller
p/n: 70-4813-62
This Window Regulator Arm Roller is designed from the original part for superior fitment and function. This nylon roller fits to the window regulator arm to lower and raise the side windows.