Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Brake or Clutch Pedal Pad
p/n: 20-0177-22
Brake or Clutch Pedal Pad - Four (4) inches long by two and three eights (2-3/8) inches long outside to outside measurements.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Hood to Cowl Bumper
p/n: 70-3306-42
Bumper, hood-to-cowl. Mounts with screws on cowl directly behind the hood to cowl seal. 2 needed per car.
Battery Box Dust Shield
p/n: 70-4460-17
This Battery Box Dust Shield is designed from the original part for superior fitment and function. The part is die cut from original style masticated rubber for a top quality part.
Axle Rebound Pad
p/n: 20-2729-32
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Headlight Grommet
p/n: 20-0142-14
Grommets, headlight wiring through radiator support. Requires one (1) per car.
Hood Bumper
p/n: 20-0207-42
Bumper, hood on fender. Push-in type. Three fourths (3/4) inch wide. Four (4) piece set.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Rear Bumper Arm Seal
p/n: 20-0234-47
This four (4) piece Rear Bumper Arm Seal set installs between the body and rear bumper. A reproduction designed from original part so it fits correctly.
Torsion bar bushing
p/n: 20-0670-36
Bushing, front radius rod. Front and rear. Four (4) required per Truck.
Transmission Filler Flaps
p/n: 70-3686-25
This Transmission Filler Flap pair is designed from the original part for superior fitment and seal. For Cutlass and 442 models with automatic transmission. Two (2) piece filler flap pair located where the frame meets the firewall on the right and left sides.
Taillight Lens Gaskets
p/n: 20-1011-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens and taillight housing. For all models except Station Wagons.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3069-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.