Rear View Mirror Mounting Pad
p/n: 70-2791-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is one (1) door mounted rear view mirror.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Accelerator Pedal Rod Grommet
p/n: 20-0044-41
This Accelerator Pedal Rod Grommet is used to wrap around the accelerator rod at the firewall. Designed from the original part for superior fit and seal.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Firewall to Hood Weatherstrip
p/n: 20-2749-42
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body. Includes attaching clips pre-installed.
Adjustable Hood Bumper
p/n: 70-2830-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires three (3) per vehicle.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Parking Light Lens Gaskets
p/n: 20-0166-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Vent Window Frame Seal
p/n: 20-1112-56
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
Cowl End Weatherstrips
p/n: 70-4917-43
This Cowl End Weatherstrip pair is designed from the original part for superior fitment and function. Die cut from correct sponge rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Quarter Panel Drain Plugs
p/n: 20-2769-45
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
Steering Column Lower Flange Insulator
p/n: 20-1532-88
This Steering Column Lower Flange Insulator is designed from the original part for superior fitment and function. This insulator fits around the lower steering column inside the vehicle to prevent metal to metal contact.
Steering Column To Floor Seal
p/n: 20-1071-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Taillight Lens Gaskets - Station Wagon
p/n: 20-1012-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens and taillight housing. For Station Wagon models.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Hood Bumper
p/n: 25-0089-42
Bumper, hood to fender. Four (4) to six (6) per car.Length: 1.5625 inches. Width: .875 inches.
Fresh Air Vent Door Seals
p/n: 70-4166-88
This two (2) piece Fresh Air Vent Door Seal pair is designed from the original part for superior fitment and seal. Seal pieces are manufactured from top quality sponge rubber to original specifications.
Steering Column - Floor Seal
p/n: 70-3499-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Tailgate Lower Seal
p/n: 70-4010-85
This Tailgate Lower Seal is properly molded from originals for a factory like fit. The seal is installed using screws, which are included.
Frame To Fender Seals
p/n: 70-3070-45
This Outer Frame to Fender Seal pair is designed from the original part for superior fitment and function. Frame seals are die cut from quality masticated rubber to authentic original dimensions.
Gearshift Knob
p/n: 20-0630-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part has a recessed end just as the factory original. This is a direct push on replacement for that broken, aged-out original knob.
Parking Light Lens Gaskets
p/n: 20-0045-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Radiator Shroud Seal
p/n: 20-0182-31
Seal, radiator side air deflector. One and five eighths (1-5/8) inch by twelve and one half (12-1/2) inch.
Tailgate Bumper
p/n: 20-0801-45
This Tailgate Bumper is used as a retaining support. Two (2) are required per truck.
Upper Control Arm Bumper
p/n: 20-2725-32
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Hood to Fender Bumper Set
p/n: 20-1312-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Windshield Frame Lower Weatherstrip
p/n: 70-4477-52
This Windshield Frame To Body Lower Weatherstrip is designed from the original part for superior fitment and sealing. This is the lower windshield frame hinge weatherstrip. It mounts to seal between the windshield frame and the cowl with the bead facing to the inside of the vehicle.
Bronco Script Brake OR Clutch Pedal Pad
p/n: 70-4480-22
This reproduction Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedals for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Tailgate Handle Gasket
p/n: 70-3867-86
This Tailgate Handle Gasket is die-cut sponge rubber to authentic original dimensions.
Trunk Lock Emblem Gasket
p/n: 70-0875-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact profile.Width: 1.875 inches. Height: 1.9375 inches.
Folding seat bumper
p/n: 20-2883-88
Bumpers, fastback fold down seat frame side. Four (4) piece set.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
Shifter Bushing Set - Column Shift
p/n: 20-1435-26
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Body hole plug
p/n: 20-2888-88
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Parking Light Lens Gaskets
p/n: 20-1025-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Parking Light to Body Mounting Pads
p/n: 20-2676-16
This Parking Light to Body Mounting Pad pair is designed from the original part for superior fitment, finish and function. This reproduction mounting pad fits between the Parking Light Assembly and body of the vehicle.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
PCV valve grommet
p/n: 20-2695-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Side window bumper
p/n: 20-2783-62
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Back Up Light To Body Gaskets
p/n: 20-2689-17
This Back Up Light To Body Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the backup light and the rear vehicle body.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
AC Hose Firewall Grommet
p/n: 20-2721-31
This A/C Hose Firewall Grommet is used to run the hoses through the firewall. Can be used with reproduction hoses. The grommet has larger holes than original.
Front Fender or Quarter Panel Extensions
p/n: 20-2761-45
This Front Fender or Rear Quarter Panel Extension pair is designed from the original part for superior fitment and seal. The pair comes as one solid unit that is perforated for the customer to split apart and is easy to install.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
AC Hose Firewall Grommet
p/n: 20-2720-31
This A/C Hose Firewall Grommet is used when running the air conditioner hoses through the firewall. Used with original style hoses.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Trunk Decklid Bumpers
p/n: 70-2044-87
This Trunk Decklid Bumper pair is designed from the original part for superior fitment, finish and function. These rubber bumpers attach to the trunk decklid to support / cushion lid closure.
Fender To Hood Side Cushion Bumper
p/n: 70-2610-42
This Fender To Hood Side Cushion Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
License Plate Light Lens Gasket
p/n: 70-3497-17
This License Plate Light Lens Gasket is designed from the original part for superior fitment and seal. This gasket fits between license plate light lens and housing.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Hood Bumper
p/n: 70-0866-42
This Hood Bumper is a quality reproduction of the original factory part. The hood bumpers provide a cushion for the hood closure that also minimizes vibration.
Hood, Door Or Liftgate Bumpers
p/n: 20-0907-71
This Hood, Door Or Liftgate Bumper pair is a quality reproduction of the original factory part.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
PCV valve grommet
p/n: 20-2697-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Accelerator Pedal Rod Seal
p/n: 20-0128-41
This Accelerator Pedal Rod Seal is used to wrap around the accelerator rod linkage at the firewall. Designed from original part so it fits correctly.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
3/4" Door Weatherstrip
p/n: 70-0236-73
This weatherstrip was designed for 1964–1966 Chevrolet and GMC truck doors but with its generic shape, has many uses outside of its original purpose.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Gearshift Seal
p/n: 20-2875-88
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.