Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Hood to Cowl Bumper
p/n: 70-3306-42
Bumper, hood-to-cowl. Mounts with screws on cowl directly behind the hood to cowl seal. 2 needed per car.
Battery Box Dust Shield
p/n: 70-4460-17
This Battery Box Dust Shield is designed from the original part for superior fitment and function. The part is die cut from original style masticated rubber for a top quality part.
Axle Rebound Pad
p/n: 20-2729-32
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Torsion bar bushing
p/n: 20-0670-36
Bushing, front radius rod. Front and rear. Four (4) required per Truck.
Transmission Filler Flaps
p/n: 70-3686-25
This Transmission Filler Flap pair is designed from the original part for superior fitment and seal. For Cutlass and 442 models with automatic transmission. Two (2) piece filler flap pair located where the frame meets the firewall on the right and left sides.
Air Cleaner Lid Gasket
p/n: 20-2700-20
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for 302, 351 and 390 V8 engine models.
Door Handle Gasket Set
p/n: 70-3321-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Vent Window Division Post Weatherstrips
p/n: 70-1921-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division post with rivets and seal as the vent glass closes against them. Fully molded with metal core and pre-drilled holes.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Convertible Top Weatherstrip Fastener Set
p/n: 70-4759-67
This sixteen (16) piece Convertible Top Weatherstrip Fastener Set is designed from the original part for superior fitment, finish and function. An exact copy of originals. The set includes 16 zinc plated special tube nuts and 16 special washers.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Front suspension bumper
p/n: 20-1062-32
Bumper, front suspension. Bumper section is 1-5/8" tall, 2" long, and 1-3/8 wide.
Heater Core Housing Gasket
p/n: 70-4469-31
This Heater Core Housing gasket is designed from original parts for superior fitment and sealing. This quality manufactured gasket fits to seal the heater core to the heater core housing.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Splash Apron
p/n: 20-0878-44
This two (2) piece Splash Apron is designed from the original part for superior fitment and seal. Front fender apron to firewall lower seal. Staples included.
Splash Apron / A-Arm Dust Shield
p/n: 70-3361-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Steering Column at Floor Seal
p/n: 70-3693-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Back Up Light Lens Gasket Set
p/n: 20-1032-17
This four (4) piece Back Up Light Lens Gasket Set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the back-up light lens and the back-up light housing or light bezel. Two (2) gaskets per lens for Station Wagon and Ranchero models.
Back Up Light Lens Gasket Set
p/n: 20-1031-17
This four (4) piece Back Up Light Lens Gasket Set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the back-up light lens and the back-up light housing or light bezel. Two (2) gaskets per lens.
Taillight Lens Gasket
p/n: 20-0837-15
Gaskets, taillight lens. Rectangular type. For style-side trucks.
Taillight Lens Gasket
p/n: 20-0747-15
Gaskets, taillight lens. Square type. Useage: 1967-72: F100-350 Trucks EXCEPT Style-side 1973-77: F100-250 series Flare-side pickups before Serial #020,000.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Front Stabilizer Bar End Link Set
p/n: 20-0037-33
This eleven (11) piece Front Stabilizer Bar End Link Set is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Steering Column At Floor Seal
p/n: 70-4629-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Firewall to Hood Weatherstrip
p/n: 20-2750-42
This Firewall to Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Hood Bumper
p/n: 70-0987-42
Bumper assembly, with stud. Two (2) or four (4) used per car as required.Height: 3.25 inches.
Vent Window Frame Seal
p/n: 20-1112-56
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
Cowl End Weatherstrips
p/n: 70-4917-43
This Cowl End Weatherstrip pair is designed from the original part for superior fitment and function. Die cut from correct sponge rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Quarter Panel Drain Plugs
p/n: 20-2769-45
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
Steering Column Lower Flange Insulator
p/n: 20-1532-88
This Steering Column Lower Flange Insulator is designed from the original part for superior fitment and function. This insulator fits around the lower steering column inside the vehicle to prevent metal to metal contact.
Steering Column To Floor Seal
p/n: 20-1071-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Taillight Lens Gaskets - Without Reflectors
p/n: 20-1014-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens and taillight housing. For vehicle models WITHOUT reflectors.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Door Glass Flexible Run Channel
p/n: 20-0894-58
This Door Glass Flexible Run Channel is designed from the original part for superior fitment, finish and function. This felt lined door glass run inserts into the top and backside of the door. Allows door glass to roll up and down freely.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Door Hinge Seal Set
p/n: 20-0909-73
This four (4) piece Door Hinge Seal set is designed from the original part for superior fitment and seal. This Door hinge to door seal set is for both doors.
Fresh Air Vent Door Seals
p/n: 70-4166-88
This two (2) piece Fresh Air Vent Door Seal pair is designed from the original part for superior fitment and seal. Seal pieces are manufactured from top quality sponge rubber to original specifications.
Tailgate Lower Seal
p/n: 70-4010-85
This Tailgate Lower Seal is properly molded from originals for a factory like fit. The seal is installed using screws, which are included.
Frame To Fender Seals
p/n: 70-3070-45
This Outer Frame to Fender Seal pair is designed from the original part for superior fitment and function. Frame seals are die cut from quality masticated rubber to authentic original dimensions.
Gearshift Knob
p/n: 20-0630-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part has a recessed end just as the factory original. This is a direct push on replacement for that broken, aged-out original knob.
Parking Light Lens Gaskets
p/n: 20-0045-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Tailgate Bumper
p/n: 20-0801-45
This Tailgate Bumper is used as a retaining support. Two (2) are required per truck.
Taillight Lens Gaskets - With Reflectors
p/n: 20-1013-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens and taillight housing. For vehicle models with reflectors.
Windshield Frame Lower Weatherstrip
p/n: 70-4477-52
This Windshield Frame To Body Lower Weatherstrip is designed from the original part for superior fitment and sealing. This is the lower windshield frame hinge weatherstrip. It mounts to seal between the windshield frame and the cowl with the bead facing to the inside of the vehicle.
Bronco Script Brake OR Clutch Pedal Pad
p/n: 70-4480-22
This reproduction Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedals for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Windshield Molding Joint Cover With Wide Moldings
p/n: 70-4483-52
This Windshield Molding Joint Cover is designed from the original part for superior fitment and usage. This cover is made from Stainless Steel to cover the molding joint where the Windshield rubber comes together.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Kick Panel Vent Gaskets
p/n: 70-4919-88
This Kick Panel Vent Gasket pair is designed from the original part for superior fitment and function. Can be used on trucks with or without A/C.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Tailgate Handle Gasket
p/n: 70-3867-86
This Tailgate Handle Gasket is die-cut sponge rubber to authentic original dimensions.
Taillight Lens Gaskets
p/n: 20-1015-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens and taillight housing. For all models except Station Wagons and Ranchero.
Trunk Lock Emblem Gasket
p/n: 70-0875-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact profile.Width: 1.875 inches. Height: 1.9375 inches.
Folding seat bumper
p/n: 20-2883-88
Bumpers, fastback fold down seat frame side. Four (4) piece set.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Outer Edge of Vent Window to Door Seal
p/n: 20-2785-62
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
Shifter Bushing Set - Column Shift
p/n: 20-1435-26
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Body hole plug
p/n: 20-2888-88
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Parking Light Lens Gaskets
p/n: 20-1025-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
PCV valve grommet
p/n: 20-2695-20
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Side window bumper
p/n: 20-2783-62
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.