Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Roof Rail Filler
p/n: 70-0396-67
Fillers, side roof rail to front roof rail at front corner, right and left. Metal core, threaded for original screws.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Running Board Edge Seal
p/n: 70-0358-45
Seal strip, running board to body lower edge, exact copy. Top quality, each strip six (6) foot long. Length: 72.0 inches. Height: .5625 inches.
Running Board Matting Cover
p/n: 20-1602-49
This Running Board Matting Cover pair is designed from the original part for an authentic fit and finish.
Running Board Mounting Pad
p/n: 20-1603-49
Grommets, running board to frame and front fender to cowl. Rubber grommets and metal washers. Twenty four (24) piece set.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Running Board To Body Filler
p/n: 70-1116-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a forty (40") inch pair of filler strips.
Running Board To Body Filler
p/n: 70-1117-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a sixty-four (64") inch pair of filler strips.
Shift Lever Bushing
p/n: 70-2026-26
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shift Linkage Repair Set
p/n: 20-2460-26
This column Shift Linkage Repair set is designed from the original parts for superior fitment and function. This repair set replaces worn or missing bushings at the four linkage points in the column shift mechanism.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Bushing
p/n: 70-0545-33
Bushing, rear shock absorber link, upper and lower end. Seven eighths (7/8) inch outside diameter, nine sixteenths (9/16) inch inside diameter, thirteen sixteenths (13/16) inch long. Four (4) per car.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Roof Rail Weatherstrip
p/n: 70-0155-65
Weatherstrip, convertible roof rail. Available by the foot.
Side Roof Rail Weatherstrip
p/n: 70-0251-65
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
Side Window Leading Edge
p/n: 30-0475-57
Weatherstrip, quarter window leading edge.Length: 12.125 inches. Width: .8125 inches.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel and Beltline Set
p/n: 20-1622-60
This six (6) piece Side Window Run Channel and Beltline set is designed from the original part for superior fitment and function. This door glass anti-rattler set includes fastener hardware and comes ready to install.
Side Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Side Window Weatherstrip Deluxe Set
p/n: 90-3737-90
This Side Window Weatherstrip Deluxe Set is for both truck doors and includes the back edge of vent window weatherstrip installed, beltline weatherstrips, door glass runs with rivets and original-type vent bar channel with brackets riveted in place.
Side Window Weatherstrip Set
p/n: 70-4633-60
This Side Window Weatherstrip Set is for both truck doors and includes the window felt beltline weatherstrips, door glass runs and original-type vent division bar channels. This is a basic replacement set with no run channel clips or division bar brackets.
Side Window Weatherstrip Set
p/n: 90-3288-90
This six (6) piece Side Window Weatherstrip Set is designed for superior fitment and function. The set contains the flexible run channels and the window felt beltline weatherstrips needed for the side window glass. The set does two (2) front doors.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
Spring eye bushing
p/n: 10-0131-35
Bushing, spring eye, both eye leaf and shackle. Front and rear.Qty Required:20 Twelve (12) required per front, eight (8) required per rear.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Spring Shackle Bushing Set
p/n: 20-1581-33
This Spring Shackle Bushing Set is for the rear leaf springs. This set is an original steel stud type.
Spring Shackle Bushing Set
p/n: 20-1580-33
This Spring Shackle Bushing Set is for the front leaf springs. This set is an original steel stud type.
Spring Shackle Pin Neoprene Washer
p/n: 70-1125-33
This Spring Shackle Pin Neoprene Washer is designed from the original part for superior fitment and function. Rubber washer fits the front and or rear spring shackle pin. Constructed of neoprene rubber.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steel Sash Channel - Door Glass
p/n: 20-0473-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This left or right door glass channel fits in the bottom of door for the glass to sit in.
Steering Column Cushion
p/n: 40-0422-36
Insulator set, steering housing to frame. Set includes both inner and outer pieces.Length: 4.125 inches.
Steering Column Cushion
p/n: 20-0453-36
This Steering Column Cushion is the steering column bracket to dash pad. This cushion is used as a noise reducer.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Floorplate
p/n: 20-0449-88
Seal, brake, clutch and steering column to floor. Column shift models. Installs under metal plate at floor.
Steering Column Floorplate
p/n: 20-0450-88
Seal, brake, clutch and steering column to floor. Floor shift models.
Steering Column Floorplate
p/n: 20-0451-88
Seal, steering column to floor mat. Column shift models. Installs on top of mat.
Steering Column Floorplate
p/n: 20-0452-88
Seal, steering column to floor mat. Floor shift models. Includes hold down clips.
Steering Column Gasket
p/n: 60-0435-32
This Steering Column Gasket is designed from the original part for superior fitment and sealing. Gasket is die cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.