Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Lower Tailgate Outer Weatherstrip
p/n: 70-4810-84
This Lower Tailgate Outer Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the outer bottom of the tailgate.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Door Handle Gasket Set
p/n: 60-0352-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Air ventilator seal
p/n: 20-2967-31
Grommet, air ventilator duct cable to firewall.Qty Required:2 Two (2) required per car.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Gravel shield bumper
p/n: 20-2956-28
Pads, front stone deflector to bumper arm anti-rattler. One (1) required per car.
Fresh Air Gasket
p/n: 20-2962-31
Seal, radiator air deflector to top of radiator. Twenty (20) inches long.
Splash Apron
p/n: 20-1320-45
This Splash Apron pair is designed to original specifications for superior fitment and proper seal. For front fender apron to frame front splash shield. Installation staples included.
Radiator Stone Deflector Seal
p/n: 20-2954-28
Seal, front stone deflector to radiator. Nineteen and three fourths (19-3/4) inches long.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Body Mounting Pad
p/n: 70-1430-48
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
2-1/4" Trunk Floor Pan Plug
p/n: 70-2598-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
Rear Spring Bushing
p/n: 60-0208-32
This Rear Spring Bushing pair is designed from the original part for superior fitment and function. Bushings are for the rear spring, shackle eye, and spring eye. Up to twelve (12) per car.
Ventilator Air Valve Gaskets
p/n: 20-2966-31
This Ventilator Air Valve Gasket pair is designed from the original part for superior fitment and seal.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Adjustable Hood Bumper
p/n: 70-0935-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
1-11/16" Main Harness Firewall Grommet
p/n: 70-2606-20
This Firewall Grommet fits to the engine firewall where main wire harness plugs in. Designed from the original part for superior fitment and finish.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
1-5/16" Firewall Grommet
p/n: 32-0347-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wiper control cable and heat tube.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
1-13/16" Trunk Floor Pan Plug
p/n: 70-2599-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
Lower Engine Mount
p/n: 20-0588-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation. One (1) required per truck.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
1-1/16" Trunk Weatherstrip
p/n: 70-0650-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
Back-up Light Gaskets
p/n: 20-1249-17
This Back-up Light Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the Back-up Light Housing to the vehicle body.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Taillight Gaskets
p/n: 60-0671-15
This Taillight To Fender Gasket pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per vehicle.
Vent division bar weatherstrip
p/n: 20-0708-56
Front vent window division post seal. Extruded rubber strip only that will have to be attached to division post.
3/4" Trunk Weatherstrip
p/n: 70-0463-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Door Handle Mounting Pad
p/n: 20-0577-86
Outside Door Handle Mounting Pad - Designed from an original part so it fits correctly.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.