Firewall Seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Cab Running Board Seal
p/n: 20-0519-45
This Cab Running Board Seal installs between the bottom of the cab and the running board. Sold as a pair for the left and right side.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Roof emblem mounting pad
p/n: 70-2575-88
Pad, roof emblem mounting gasket. Machine die cut sponge rubber to exact required shape.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Side Window Vertical Leading Edge
p/n: 20-3126-80
Side window vertical leading edge weatherstrip. Cut to length. NOT cloth covered. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Designed from the original part for superior fitment and seal.
Fender Skirt Edge Weatherstrip
p/n: 20-3019-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mounting Pad
p/n: 30-0500-48
Pad, body mounting. Fully molded rubber with locating collar and metal core. Number used varied according to body type.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Parking Brake Pedal Pad
p/n: 25-0071-22
Pad, parking brake pedal.Length: 2.125 inches. Width: 2.0 inches.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Front Bow Weatherstrip
p/n: 60-0200-64
This convertible top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top between the folding soft top and the top of the outer windshield.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Hood Bumper Set
p/n: 33-0681-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Convertible Front Bow Weatherstrip
p/n: 60-0253-64
This Convertible Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the rear center section.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Backup light gasket
p/n: 20-1246-17
Gaskets, back-up light cover. Used on models without back-up lights.
Windshield Post to Door Weatherstrips
p/n: 20-3093-63
This Windshield Post To Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips attache to the body and seal between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Hood to Radiator Weatherstrip
p/n: 20-2961-31
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 60-0119-48
This Body Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with metal core and metal bolt liner.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Front Header Bow Weatherstrip
p/n: 20-3097-64
This convertible top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top to seal between the soft top and the top of the windshield.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Hood Bumper Set
p/n: 20-0545-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F Series Trucks.
Stabilizer bushing
p/n: 20-1295-33
Bushings, stabilizer bar to frame. One (1) pair required per car.
Fender Anti-Squeak Weatherstrip
p/n: 20-1864-45
This Fender Anti-Squeak Weatherstrip mounts between the front fender splash apron and the front fender. The weatherstrip is an exact reproduction of the original Ford part. Sold as a seventy-two (72") inch strip.
Cowl Vent Gasket
p/n: 20-0556-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Door Lock Bumper
p/n: 70-0933-71
Bumper, door lock pillar, upper. Two (2) car.Length: 1.625 inches. Width: 1.0 inches.
Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
1-5/8" Firewall Grommet
p/n: 70-2062-20
This Firewall Grommet is used to run the oil pressure and temperature line through the firewall. Designed from original parts for excellent workmanship
1-5/8" Firewall Grommet
p/n: 70-2064-20
This Firewall Grommet is used to run the vacuum hose and ignition resistor wire through the firewall. Designed from the original part for excellent workmanship.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
1-5/8" Firewall Grommet
p/n: 70-2063-20
This Firewall Grommet is used to run the speedometer cable line through the firewall. Designed from original part for excellent workmanship.