Stabilizer Bar End Link Repair Set
p/n: 20-1294-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar Frame Bushing Set
p/n: 20-1842-33
This twenty-six (26) piece Stabilizer Bar Frame Bushing Set is for the front and allows the rod to flex and rotate, but stays in place where it is attached to the vehicle frame.
Stabilizer Bar To Frame Bushing Set
p/n: 20-1844-33
This four (4) piece Stabilizer Bar To Frame Bushing Set mounts on the sway bar to frame. Bushings can crack, dry out, and harden resulting in squeaks.
Stabilizer Bushing
p/n: 27-0085-34
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement.
Stabilizer bushing
p/n: 20-1295-33
Bushings, stabilizer bar to frame. One (1) pair required per car.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Standard bumper
p/n: 20-1852-41
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Floorplate
p/n: 20-0587-36
This Steering Column Floorplate pad wraps between the steering column and bracket. The pad is used to reduce noise between the steering column and the dash.
Steering Column Floorplate
p/n: 70-1425-88
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Steering Column Floorplate
p/n: 20-1782-88
Seal, steering column to floor. Installs under floor mat.
Steering Column Floorplate
p/n: 50-0412-36
Floorplate, steering column. Metal core just like the original.
Steering Column Grommet
p/n: 70-2316-88
Grommet, steering column at floor. Order our #70-2316-88 seal separately.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Stone Deflector Seal
p/n: 20-1869-47
This Stone Deflector Seal is designed from an original part so it fits correctly. This seal installs between the body and rear bumper. Comes with installation staples.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Tailgate bumper
p/n: 70-2854-87
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Tailgate or Back Door Weatherstrip
p/n: 70-3604-84
This Tailgate or Back Door Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.
Tailgate wedge
p/n: 70-2855-87
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
Taillight Gasket Set
p/n: 30-0460-15
This eight (8) piece Taillight Gasket set is designed from the original part for superior fitment and seal. This reproduction set includes all lens and light body gaskets for both sides.
Taillight Lens Gasket
p/n: 70-3091-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Taillight Lens Gasket
p/n: 70-0951-15
Gasket, taillight lens. Die cut one eighth (1/8) inch sponge rubber. Note: Sixty Special (60 Special) will require two (2) pairs.
Taillight Lens Gaskets
p/n: 20-1229-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Taillight To Body Gaskets
p/n: 70-3766-15
This Taillight To Body Gasket pair is designed from the original part for superior fitment and sealing. Installs under the taillight assembly. Die cut masticated rubber to authentic original dimensions.
Taillight to Body Weatherstrips
p/n: 70-0701-15
This Taillight To Body Weatherstrip pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Twenty-three and three fourths (23-3/4) inches developed length.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Transmission Mount
p/n: 20-1269-11
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.