Axle Bumpers
p/n: 60-0491-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming rebound pads are dense rubber blocks that mount to the rear axle tube.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Rigid Run Channel
p/n: 60-0073-58
Channel, rigid division bar. Un-beaded, cloth covered, mohair lined. Perfect replacement requires drilling for screws.
Rear Wheelhouse To Quarter Panel Fillers
p/n: 60-0354-45
This Rear Wheelhouse To Quarter Panel Filler pair is for the outer rear wheelhouse panel to quarter panel. Sold as a five (5) foot filler pair, one for each side.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Automatic Transmission Mounts
p/n: 60-0234-11
This Automatic Transmission Mount pair supports the transmission and dampens vibration. Engineered and designed to OE standards. Steel core as original.
Door Glass Run Channel
p/n: 20-0510-58
This Door Glass Run Channel is designed from the original part for superior fitment and function. Stainless beaded edge channel with clips pre-installed. Enough for one door only.
Steel Sash Channel - Left Front Side
p/n: 20-3055-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Left Front Door.
Steel Sash Channel - Right Front Door
p/n: 20-3054-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This glass channel is for the Right Front Door.
Vent Division Bar Assembly
p/n: 20-0565-56
Assembly, complete division bar. Right-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Vent Division Bar Assembly
p/n: 20-0566-56
Assembly, complete division bar. Left-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Front Suspension Bumpers
p/n: 40-0251-32
This Front Suspension Bumper pair for the upper arm is made from high-quality EPDM dense rubber for a precise, factory like fit. Two (2) required per car.
Window Felt Beltline Weatherstrips
p/n: 80-0636-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece anti-rattler set includes inner and outer window felt beltline weatherstrips for each door side window and quarter window.
Division bar bumper
p/n: 70-1443-62
Bumper, upper division post. Molded rubber part with a brass core.
Front Door Weatherstrips
p/n: 20-0559-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Door gaskets mount directly to seal the full perimeter of both the front left and front right doors to the body.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Skirt Edge Seals
p/n: 70-0897-44
Fender Skirt Edge Seal pair. Length: 60.0 inches. Width: 5/8 inches.
Steering Column Grommet
p/n: 60-0436-32
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.
Door Edge Weatherstrips
p/n: 60-0030-73
This Door Edge Weatherstrip pair is designed from the original part for superior fitment and sealing. These primary door weatherstrips mount directly to the vehicle body.
Fixed Rear Quarter Window Weatherstrip
p/n: 70-3871-77
This Fixed Rear Quarter Window Weatherstrip set contains two (2) seals for the fixed windows on the rear quarter of the vehicle. These seals fit the front or rear quarter windows.
U Jamb lock pillar filler
p/n: 50-0307-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Rear Window Gasket Set
p/n: 70-2312-83
This Rear Window Gasket Set contains the rear window gaskets themselves and the locking strips. Four (4) piece set mounts around the two (2) separate back windows. The ends may require trimming and bonding for installation.
Body Bumper Kit
p/n: 90-0213-90
This sixteen (16) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Running Board To Body Filler
p/n: 70-1117-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a sixty-four (64") inch pair of filler strips.
Axle Rebound Pad
p/n: 27-0081-32
Bumper, rear axle on leaf spring.Width: 3.25 inches. Height: 4.75 inches.
Rear Bumper Seal
p/n: 70-1830-45
Seal, rear bumper to body. Includes two (2) thirty (30) inch strips of extrusion.Length: 30.0 inches. Width: 2.4375 inches.
Window Felt Beltline Weatherstrips
p/n: 80-0056-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set includes inner and outer window felt beltline weatherstrips for each door side window.
Door Weatherstrip
p/n: 30-0327-73
Weatherstrip, front door, right and left, lock side on door upper corner. Designed to attach to our #70-0219-73 weatherstrip.Length: 3.25 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Rear Split Small Window Gasket
p/n: 70-4905-83
This Rear Split Small Window Gasket mounts around the full perimeter of the rear back glass for a precise, factory fit. This gasket is for models with the two (2) small rear windows. Two (2) are required per vehicle. It is a standard black gasket without a trim groove.
Hinge Pillar Weatherstrip
p/n: 20-3094-63
Convertible Hinge Pillar Weatherstrip - To seal along the windshield post and over across the top.
Hinge Pillar Weatherstrip
p/n: 70-1523-73
Weatherstrip, upper front door hinge pillar at roof rail. Molded as left and right with corrosion resistant brass metal core.
Division Bar Grommet
p/n: 70-3132-62
Grommets, rear door vent divider post, upper and lower, right and left. 4 piece set.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Rear Window Gasket
p/n: 60-0469-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 60-0182-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a thirteen foot, one inch (13' 1") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Gas Tank Filler Upper Seal
p/n: 70-3701-39
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Trunk Weatherstrip
p/n: 50-0483-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Hardtop Weatherstrip
p/n: 70-2012-68
Weatherstrip, hardtop roof rail, auxiliary. Installed in side window flipper seal. This is a factory service department fix designed to reduce wind noise on 56th series hardtops that also can be used on 55th series models.
Quarter window weatherstrip
p/n: 70-3396-77
Seal, rear fixed quarter window seal. Fully molded replacement.
Taillight Gasket Kit
p/n: 70-0972-15
Gasket set, taillight and backup light assembly to fender. Four (4) piece set.
Upper Tailgate Weatherstrip
p/n: 20-3143-85
This Upper Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the top of the tailgate.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Roof Rail Filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Molded as left and right with a corrosion resistant brass metal core.
Engine Mount Service – Revulcanization Only
p/n: 25-0073-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Door Vent Window Weatherstrips
p/n: 38-0060-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Trunk Weatherstrip
p/n: 70-1691-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Door Weatherstrip
p/n: 30-0468-73
Weatherstrip, door hinge pillar. Molded rubber ends attached to sponge rubber extrusion replacement. Length: 36.0 inches.
Side Window Leading Edge
p/n: 30-0388-57
This Side Window Leading Edge pair attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Made of a quality EPDM dense rubber, these weatherstrips help to keep the elements out and reduce road noise while driving.
Engine Mount Service – Revulcanization Only
p/n: 25-0063-11
This Revulcanization Service Only is designed to restore your Upper Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Door Edge Weatherstrips
p/n: 60-0247-72
This Door Edge Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. These door edge weatherstrips mount, with pre-installed pins, to seal the Left and Right doors when closed.
Rear Window Gasket
p/n: 70-1729-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Bow Weatherstrip
p/n: 70-2296-64
Weatherstrip, windshield header bow to convertible top. Fully molded, exact original profile configuration with attached molded ends.
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Rear Window Gasket
p/n: 20-1385-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Front Suspension Bumper
p/n: 40-0250-32
Bumper, front suspension, lower arm. Two (2) per car.Width: 3.0 inches. Height: 1.625 inches.
Rear Window Gasket
p/n: 60-0609-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 70-1867-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Windshield Gasket
p/n: 70-2468-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 60-0265-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Rear Cargo Door Weatherstrips - Panel Truck
p/n: 20-0579-73
This Rear Cargo Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Rear Window Gasket Set
p/n: 70-1623-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Front Suspension Bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Spring Shackle Bushing Set
p/n: 20-0550-32
This Spring Shackle Bushing Set is used on both springs. This kit does NOT include the shackle bars used on the front of the spring.
Engine Mount Service – Revulcanization Only
p/n: 40-0410-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.