Door Handle Gasket Set
p/n: 70-2673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 70-1913-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Door Handle Gasket Set
p/n: 50-0494-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Door Handle Gasket Set
p/n: 70-0979-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Firewall Seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3007-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. A reproduction using dense rubber extrusion and tack fasteners.
Side Window Bumper
p/n: 20-3086-62
Bumpers, upper door glass. Installs on backside top of vent window frame where window rolls up against it.
Beltline Weatherstrip
p/n: 60-0287-58
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Cab To Frame Mounting Pad Set
p/n: 20-0554-45
This ten (10) piece Cab To Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fuel Neck Grommet
p/n: 60-0475-41
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3-1/2") outside width by three and fifteen sixteenths inch (3-15/16") outside length.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Stabilizer Bar End Link Repair Set
p/n: 20-1294-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Roof Rail Filler
p/n: 60-0429-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes. High-quality EPDM rubber a solid brass core.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Clutch Rod Boot
p/n: 20-2949-23
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Windshield Frame To Cowl Weatherstrip
p/n: 70-3004-42
This Windshield Frame To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This cowl rubber goes in between the windshield frame and cowl. This part also fits the 1952-1971 M38A1 model.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Body Bumper Kit
p/n: 90-0206-90
This ten (10) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Headlight to Fender Gasket
p/n: 50-0563-14
Seal, headlight to fender. Die cut to original dimensions.Height: .125 inches.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Drag Link End Repair Set
p/n: 20-0506-32
This Drag Link End Repair set is designed from the original parts for superior fit and function. This repair set will help your worn and aged steering connections to be once again as tight as the factory made them and help to make steering your classic truck easy again.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Steering Column Finish Strip
p/n: 70-1707-88
Seal, steering column to instrument panel. Extruded rubber strip thirteen (13) inch to exact cross-section.Length: 13.0 inches. Width: .625 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Fender Skirt Edge Weatherstrip
p/n: 20-1316-44
This Fender Skirt Edge Weatherstrip pair is designed from original for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Vent division bar weatherstrip
p/n: 20-3042-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood Bumper Set
p/n: 20-3004-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Splash Apron
p/n: 20-3016-44
This six (6) piece Splash Apron set is designed from the original part for superior fitment and seal. Installs on fender splash apron and bottom of radiator side deflectors.
Vent Division Bar Weatherstrips
p/n: 20-3043-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Headliner Seal
p/n: 20-0573-88
Headliner Seal - One hundred seventy six (176) inches long to hold Headliner - Goes Around The Interior Perimeter Of Cab.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Vent Window Division Post Weatherstrips
p/n: 20-0562-56
Front vent window division post seal. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Antenna Mount Pads
p/n: 70-2264-21
This Antenna Mount Pad pair is designed from the original part for superior fitment and seal. For rear mounted twin (dual) antennas. See our 32-0390-21 for insulating Antenna Grommet pair.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Wiring Harness Grommet
p/n: 70-2113-20
This Wiring Harness Grommet is designed from the original part for superior fitment and seal. The grommet installs for an authentic fit, finish and function. Fully molded with proper lips and pass through holes for main harness electrical wiring.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Steering Column Floorplate
p/n: 60-0403-24
This Steering Column Floorplate is used as the steering gear and clutch pedal push rod dash seal. Fully molded with original style pattern. Does not have metal backing.
Radiator Mounting Pad Set
p/n: 20-0570-45
This Radiator Mounting Pad Set is designed from the original parts for a factory like appearance and function.
2" Wiring Harness Firewall Grommet
p/n: 70-1724-20
This Wiring Harness Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Leading Edge Weatherstrip
p/n: 70-2002-80
Rear door window vertical seals. Fully molded rubber with metal cores.
2" Firewall Grommet
p/n: 70-1725-20
This Firewall Grommet is used to run the windshield washer hose and antenna wiring through the firewall. Designed from the original part for superior fit and seal.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.