Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Clutch Rod Boot
p/n: 20-2949-23
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Front Fender Seal
p/n: 20-3010-44
This Front Fender Seal installs between the splash apron to fender and the rear of the splash apron to body. Sold as a one hundred forty (140) inch strip.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Roof Rail Filler
p/n: 70-3644-73
Filler, side roof rail. Front corner, just in front of flipper seal. Right and left, solid brass core, molded screw holes.
Parking Light Lens Gasket
p/n: 50-0353-16
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Cab To Frame Mounting Pad Set
p/n: 20-0554-45
This ten (10) piece Cab To Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Gravel shield bumper
p/n: 70-2825-44
Anti-rattler, front stone shield. Insulates the front stone shield from the front bumper. Six (6) piece set.
Beltline Weatherstrip
p/n: 60-0287-58
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Parking Light Lens Gasket
p/n: 60-0672-17
This Parking Light Gens Gasket pair is die cut from one-eighth (1/8) inch sponge rubber.
Hood To Cowl Weatherstrip
p/n: 70-1698-43
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. A reproduction designed from original part so it fits correctly.
Rear Spring Pad
p/n: 70-2080-32
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Door Handle Gasket Set
p/n: 70-0979-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Parking Brake Pedal Pad
p/n: 50-0348-22
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.