Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Front Fender to Apron Seal
p/n: 20-2504-45
This Front Fender to Apron Seal installs on the fender to inner apron. Excellent for when assembling front sheet metal. Sold as a fifteen (15) foot roll.
Antenna Mount Pad
p/n: 70-2621-21
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
Fuel Neck Grommet
p/n: 10-0123-41
Grommet, fuel filler neck. Fully molded soft flexible rubber. Two and seven sixteenths inch (2-7/16") outside diameter by one and seven sixteenths inch (1-7/16") inside hole diameter by five sixteenths (5/16") height.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Trunk Handle Mounting Pad
p/n: 70-0647-86
Mounting pad, trunk handle and lock escutcheon plate.Length: 2.875 inches. Width: 1.625 inches.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Drag Link End Repair Set
p/n: 20-0506-32
This Drag Link End Repair set is designed from the original parts for superior fit and function. This repair set will help your worn and aged steering connections to be once again as tight as the factory made them and help to make steering your classic truck easy again.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Hood to Cowl Weatherstrip
p/n: 30-0233-42
Seal, hood to cowl. High quality closed cell sponge rubber construction as original.Width: .4375 inches. Height: .5625 inches.
Brake and Clutch Shank Seal
p/n: 12-0006-24
Seal, brake and clutch pedal shank to floorboard. Three eighths (3/8) inch thick, two and one half (2-1/2) inch diameter.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
License Light Mounting Pad
p/n: 50-0034-17
Pad, rear license light and trunk handle body.Length: 7.50 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Clutch and Brake Pedal Pads
p/n: 20-2450-22
This reproduction Clutch and Brake Pedal Pad pair slip over the full perimeter of the clutch and brake pedals for a precise, factory fit. Detailed and finished to match the original appearance.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Emergency Brake Cable Grommet
p/n: 20-2438-20
This Emergency Brake Cable Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Front Engine Mount
p/n: 20-2401-11
This Front Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation. Two (2) required per car.
Rear Engine Mount
p/n: 20-2400-11
This Rear Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Beltline Weatherstrip
p/n: 60-0287-58
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Fuel Filler Neck Grommet
p/n: 60-0434-41
This Fuel Filler Neck Grommet is the inner grommet through the quarter panel inside fuel filler door. Fully molded rubber with retaining flange as original for good seal. Three and one eighth inch (3-1/8") outside diameter by two and one eighth inch (2-1/8") inside diameter.
1-13/16" Firewall Grommet
p/n: 70-0453-20
This Firewall Grommet is a four (4) hole design that is used for the hood release, vacuum antenna tube, and others. Designed from the original part for superior fit and seal.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Hood Rest Pad
p/n: 30-0092-42
Hood Rest Pad. Molded rubber with a steel core. Six (6) required per car. Length: 1.75 inches Width: 1.625 inches.
2-1/2" Firewall Grommet
p/n: 30-0111-21
This Firewall Grommet is used to run the speedometer cable through the firewall. The grommet is retained by a steel collar, not included.
1-9/16" Firewall Grommet
p/n: 30-0383-21
This Firewall Grommet is used to run the vacuum antenna line through the firewall. The grommet is molded with four (4) holes but three (3) are left masked for use if needed.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.