Taillight Lens Gasket Set
p/n: 70-4916-15
This Taillight Lens Gasket set is designed from the original part for superior fitment and seal. Six (6) reproduction gaskets fit between taillight lens and taillight housing bezel.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Windshield Bumpers - Steel Core
p/n: 34-0258-52
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
1-5/16" Firewall Grommet
p/n: 32-0347-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wiper control cable and heat tube.
Tailgate Handle Gasket
p/n: 70-3867-86
This Tailgate Handle Gasket is die-cut sponge rubber to authentic original dimensions.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
1-13/16" Trunk Floor Pan Plug
p/n: 70-2599-87
This Trunk Floor Pan Plug is designed from the original part for superior fitment and seal. This plug is made from high quality EPDM dense rubber to provide excellent durability.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Taillight Lens Gaskets
p/n: 70-4170-15
This six (6) piece Taillight Lens Gasket set is a die cut sponge rubber gaskets made to authentic original dimensions. Includes right and left side gaskets. This reproduction gasket fits between taillight lens & taillight housing.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Cowl Panel to Cowl Filler Seals
p/n: 70-3695-43
This Cowl Panel to Cowl Filler Gasket pair is designed from the original part for superior fitment and function. These seals go under the cowl vent grille on the left and right sides of it.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.