Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Front Stabilizer Bushing
p/n: 70-0348-33
Bushings, front stabilizer bar mounting. Fully molded rubber. One and thirteen sixteenths inch (1 13/16") length by one and three eighths inch (1 3/8") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half inch (1 1/2") height.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Front Bumper Grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Side Deflector / Valance Rubber
p/n: 70-0092-45
This Side Deflector / Valance Rubber pair is designed from the original part for superior fitment and seal. Each deflector piece is approximately 6 feet long.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Trunk Weatherstrip
p/n: 70-0796-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.