Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Fuel Filler Neck Grommet
p/n: 60-0434-41
This Fuel Filler Neck Grommet is the inner grommet through the quarter panel inside fuel filler door. Fully molded rubber with retaining flange as original for good seal. Three and one eighth inch (3-1/8") outside diameter by two and one eighth inch (2-1/8") inside diameter.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit, finish and appearance.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Parking Light Grommet
p/n: 60-0568-17
Grommet or Nipple, parking light wire from light body. Part of assembly.Length: 1.625 inches.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Antenna Mount Pad
p/n: 60-0050-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.