Windshield Gasket
p/n: 19-0006-52
This Windshield Gasket comes in a four (4) foot strip and is for horizontally split windshields. The slot fits on the lower half and the projecting edge meets the upper half when the windshield is closed.
Axle Rebound Pad
p/n: 30-0102-32
Pads, axle rebound, block type with flange. One and one half (1-1/2) inch by one and three fourths (1-3/4) inch by two and one half (2-1/2) inch overall.
Cowl Vent Gasket
p/n: 30-0250-54
Gasket, cowl vent. Molded labyrinth style as original.Length: 13.50 inches.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Beltline Weatherstrip
p/n: 30-0301-57
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Axle Rebound Pad
p/n: 70-1289-32
Bushing, rear support arm. Rear upper. Four (4) per car. For lower see #70-1290-32.
Red Brake and Clutch Pedal Pad
p/n: 30-0114-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0114-22.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Axle Rebound Pad
p/n: 70-1290-32
Bushing, rear support arm. Rear lower. Four (4) per car. For upper see #70-1289-32.
Hood Corner Pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Taillight Mounting Pad
p/n: 30-0198-15
Mounting pad, taillight. With proper edging and shape, molded left and right. Sold only in complete pairs.Length: 9.75 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Instrument board retainer
p/n: 70-3609-20
Instrument board wind lace retainer. Both R & L sides. Anti-rattle instrument panel ends. 11 1/4" long. Replaces 310646 & 310647.
Dashboard Anti-Rattle
p/n: 30-0025-20
Anti rattle, each end of instrument panel. Beaded edge as original, eight and one half (8-1/2) inch long. Replaces 310708 & 310709.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Taillight Mounting Pad
p/n: 30-0132-15
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Taillight Mounting Pad
p/n: 30-0366-15
Pad or Gasket, taillight to body. One (1) pair required per car, sold only in pairs.
Side Mount Tire Cushion
p/n: 30-0411-37
Cushion, lower (thick) spare wheel in fender well. Two (2) per car.Length: 11.0 inches. Width: 3.0 inches.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Rear Window Gasket
p/n: 30-0086-83
This Rear Window Gasket comes in a seven (7) foot strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Division bar bumper
p/n: 70-1443-62
Bumper, upper division post. Molded rubber part with a brass core.
Gravel Shield Bumper
p/n: 30-0384-44
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
Windshield Division Bar Gasket
p/n: 30-0146-52
Gasket, windshield division bar. Molded inner and outer, fully detailed.Length: 13.625 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Steering Column Grommet
p/n: 70-1895-36
Grommet, steering column at dash. See #70-1894-36 for grommet at floorboard.Width: 2.625 inches.
Headlight Mounting Pad
p/n: 30-0133-14
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Convertible Rest Liner
p/n: 30-0257-65
Liner, folding top bow rest. Flexible high grade rubber to snap into original folding top cradle. Thirteen (13) inches long.