Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear Window Gasket
p/n: 60-0278-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spring Shackle Pin Neoprene Washer
p/n: 70-1125-33
This Spring Shackle Pin Neoprene Washer is designed from the original part for superior fitment and function. Rubber washer fits the front and or rear spring shackle pin. Constructed of neoprene rubber.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Trunk Handle / License Light Mounting Pad
p/n: 27-0035-17
This Trunk Handle and License Light Mounting Pad is designed from the original part for an authentic fit, finish, and appearance.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Trunk Weatherstrip
p/n: 70-0874-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Windshield Gasket
p/n: 60-0186-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Windshield Gasket
p/n: 70-1534-50
This Windshield Gasket is for windows without chrome reveal molding or divider bar. Mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Wiper Transmission To Cowl Gaskets
p/n: 60-0101-53
This Wiper Transmission To Cowl Gasket pair is designed from the original part for superior fitment and seal. Gaskets are precision die cut from quality dense rubber material.