Hood to Cowl Weatherstrip
p/n: 30-0233-42
Seal, hood to cowl. High quality closed cell sponge rubber construction as original.Width: .4375 inches. Height: .5625 inches.
Hood to Cowl Weatherstrip
p/n: 70-1296-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Fully molded with carrot-bumper retainers.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Horn Cover Bumper
p/n: 30-0283-21
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Instrument board retainer
p/n: 70-3609-20
Instrument board wind lace retainer. Both R & L sides. Anti-rattle instrument panel ends. 11 1/4" long. Replaces 310646 & 310647.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
License Lens Gasket
p/n: 70-2121-17
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
License Light Mounting Pad
p/n: 30-0122-17
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Lock Cylinder Gasket
p/n: 30-0022-71
Pads, door handle escutcheon.Width: 1.875 inches. Height: 1.375 inches.
Lock cylinder gasket
p/n: 30-0389-71
Gasket, door lock handle escutcheon, front and rear doors. Two (2) or four (4) required per car.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Parking Light Gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Parking Light Lens Gasket
p/n: 70-1521-16
Gasket, parking light lens.Length: 14.875 inches. Width: 2.0 inches.
Parking Light Mounting Pad
p/n: 30-0195-17
Gaskets, front parking light to fender.Length: 19.875 inches.
Parking Light Mounting Pad
p/n: 30-0447-17
Pad, parking light to fender. Requires two (2) per car.Length: 4.125 inches.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Parking Light Mounting Pad
p/n: 30-0416-17
Gasket, fender light. Faithful copy with correct shape and detail as originalLength: 2.75 inches.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1690-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Plug Wire Sleeve
p/n: 30-0204-21
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Power Steering Bushing
p/n: 70-1968-36
Bushing, power steering cylinder to frame. Two (2) required per car.Height: .625 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Prop shaft support service
p/n: 30-0526-24
Support, drive shaft intermediate bearing retainer. Revulcanization service only.
Radiator Mounting Pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Radiator Mounting Pad
p/n: 30-0451-31
Spacer or Pad, lower radiator anchor stud. Used in conjunction with our #30-0395-31.Height: .3125 inches.
Radiator mounting pad
p/n: 30-0121-31
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Radiator Mounting Pad
p/n: 30-0469-31
Pad (or Grommet), radiator to dash tie rod. Die cut from one fourth (1/4) inch rubber. Four (4) used per car.Height: .25 inches.
Radiator Mounting Pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Rear Bumper Grommet
p/n: 30-0078-29
Grommets, rear bumper. Molded left and right as original with excellent detailing. Fully molded rubber with retaining flange.
Rear Bumper Grommet
p/n: 30-0047-29
Grommets, rear bumper. For models with luggage racks. Length: 4.125 inches. Width: 3.375 inches.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Rear Bumper Grommet
p/n: 30-0127-29
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original.
Rear Bumper Grommet
p/n: 30-0197-29
Grommets, rear bumper. Molded left and right. Fully molded rubber.
Rear Bumper Grommet
p/n: 30-0137-29
Grommets, rear bumper support bar to body. Fully molded rubber w/ retaining flange.
Rear Door hinge pillar seal
p/n: 30-0496-73
Weatherstrip, rear door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.
Rear door vent weatherstrip
p/n: 30-0118-74
Rear door vent window rubber. Order our #30-0347-74 division post seal separately.
Rear Door Vent Window Weatherstrips
p/n: 30-0481-74
This Rear Door Vent Window Weatherstrip pair is designed from the original parts for superior fitment and seal.
Rear door weatherstrip
p/n: 90-0121-72
Weatherstrip, rear door kit. Includes sufficient weatherstrip for door perimeter, bottom and hinge pillar. Adhesive is not included in the kit.
Rear Door weatherstrip
p/n: 90-0147-72
Weatherstrip, rear door kit. Includes weatherstrip for door perimeter and hinge pillars.
Rear Engine Mount Service - Revulcanization Only
p/n: 30-0403-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Mount Service - Revulcanization Only
p/n: 30-0509-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Support Assembly - Revulcanization Only
p/n: 30-0328-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear quarter vent weatherstrip
p/n: 30-0187-77
Weatherstrip, rear quarter vent window. Full swing type.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0333-77
This Rear Quarter Vent Window Weatherstrip pair is designed from the original parts for superior fitment and seal. A two (2) piece pair that fits both driver (Left) and passenger (Right) sides of the rear quarter panel vent / wing window assemblies.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0249-77
This Rear Quarter Vent Window Weatherstrip pair is designed from the original part for superior fitment and seal. For full swing type rear vent windows.