Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
License Light Mounting Pad
p/n: 40-0174-17
Pad, license light mounting. Plain type without edge bead as original.Length: 8.0 inches. Width: 3.25 inches.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Hood to Radiator Weatherstrip
p/n: 40-0512-42
Weatherstrip, hood to grill or radiator shroud. Two (2) pieces, each sixteen (16) inches.Width: 1.3125 inches.
Rear Window Division Bar Seal
p/n: 40-0285-77
Gasket, back window division bar. Closed body styles with split back window.Length: 9.25 inches. Width: 1.125 inches.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
License Lens Gasket
p/n: 70-2276-16
Gasket, license light lens. Fully molded with proper details.Length: 3.0 inches. Width: 1.6875 inches.
Cowl Vent Gasket
p/n: 40-0210-54
Gasket, cowl vent. Sponge rubber. For cowl vents of thirty-four (34) inch circumference, three fourths (3/4") inch width as shown.
Cowl Vent Gasket
p/n: 40-0500-54
Gasket, cowl vent. Die cut sponge rubber to original dimensions.Length: 19.0 inches.
Door Weatherstrip
p/n: 40-0367-57
Door belt inner weatherstrip (scraper seal). Front door only. Thirty six (36) inches long.
License Light Mounting Pad
p/n: 40-0391-85
Pad, trunk handle and license light housing.Length: 5.875 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Windshield Division Bar Inner Gasket
p/n: 40-0284-52
This Windshield Division Bar Inner Gasket is designed from the original part for superior fitment and seal. This top quality EPDM rubber inner gasket fits to the inside of the windshield.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Beltline Weatherstrip
p/n: 40-0540-57
This six (6) foot Beltline Weatherstrip installs on the left and right doors to wipe the side windows when the glass is lowered. Flexible, pile lined, rubber covered, with black bead. Available in 6ft. lengths.
Fuel Neck Grommet
p/n: 70-1616-39
Grommet, fuel neck. Fully molded rubber with retaining flange. Three and eleven sixteenths inch (3-11/16") outside diameter by two and one eighth inch (2-1/8") inside hole diameter by nine sixteenths inch (9/16") height.
Side Roof Rail Weatherstrip
p/n: 30-0177-65
Side Roof Rail Weatherstrip to fit at the bottom of roof rail over the side window. Made of high-quality EPDM rubber. Fits metal retainer.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Starter pedal pad
p/n: 40-0200-21
Pad, starter pedal. Excellent quality with detail and workmanship as found in original.
Trunk Bumper
p/n: 40-0082-85
Bumper, trunk lid, rubber. Retained by two (2) screws (not included).Width: 2.50 inches. Height: 1.625 inches.
Fuel Neck Grommet
p/n: 40-0139-39
Grommet, fuel filler neck. Fully molded rubber, slightly angled. Four and one half inch (4-1/2") outside width by four and five eighths inch (4-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Hood to Cowl Weatherstrip
p/n: 70-2219-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) long original profile extrusion provides complete coverage.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Trunk Hinge Mounting Pad
p/n: 40-0134-85
Pads, trunk hinge mounting. Three and one half (3-1/2) inch and five (5) inch long sections. Sold as four (4) piece set for two (2) hinges.
Steering Column Grommet
p/n: 40-0078-36
Grommet, steering column to toe board. Black rubber. For brown see our #40-0078-89.Length: 5.375 inches.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Hood to Radiator Weatherstrip
p/n: 70-1580-42
Weatherstrip, hood to radiator shroud.Width: 1.3125 inches.
Steering Column Grommet
p/n: 40-0144-36
Grommet, steering column to toe board. Black rubber. For brown see our #40-0144-89. Two and three fourths (2-3/4) inch by seven and one half (7-1/2) inch.
Accelerator Pedal Pad
p/n: 40-0113-40
Pad, accelerator pedal. Black rubber. Slipover type. Exact pattern, perfect copy in all details.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Cowl Vent Gasket
p/n: 40-0225-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Installs for a like factory fit and finish.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Cowl Vent Gaskets
p/n: 40-0170-54
This Cowl Vent Gasket is manufactured from high quality EPDM sponge rubber. For twin cowl vents of thirty four (34") inch circumference.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Fuel Neck Grommet
p/n: 40-0091-39
Grommet, fuel filler neck. Fully molded large oval style. Bottom is flat. Four and one half inch (4-1/2") outside width by five by one half inch (5-1/2") outside length. Two and five sixteenths inch (2-5/16") inside hole diameter.
Decklid Lock Bumper
p/n: 40-0361-85
This Decklid Lock Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Brown Steering Column Grommet
p/n: 40-0078-89
Grommet, steering column to toe board. Brown rubber. For black see our #40-0078-36.Color:brown Length: 5.375 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Control Arm Bumper
p/n: 40-0465-32
Bumper, upper control arm. One (1) pair per car.Height: 1.375 inches.
Door Bottom Weatherstrips
p/n: 40-0537-73
This Door Bottom Weatherstrip pair is designed from the original part for superior fitment and seal. Held to door by steel strip. Sponge type rubber as original. For two (2) door models.
Convertible Top Front Bow Weatherstrip
p/n: 30-0503-65
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top to seal between the soft top and the top of the windshield.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Steering Column Grommet
p/n: 40-0421-36
Grommet, steering column and transmission shift rod through firewall.Length: 4.375 inches.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Fender Skirt Edge Weatherstrip
p/n: 40-0279-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Windshield Division Bar Gasket
p/n: 40-0157-52
Gasket, windshield division bar.Length: 14.0 inches. Width: 1.0 inches.
Hood to Cowl Weatherstrip
p/n: 40-0470-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) foot long x 13/16” wide weatherstrip provides complete coverage.
Brown Accelerator Pedal Pad
p/n: 40-0113-89
Pad, accelerator pedal. Brown rubber. For black see our #40-0113-40. Slipover type. Exact pattern, perfect copy in all details.
Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Front Bow Weatherstrip
p/n: 40-0418-65
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. Top quality extrusion cut five (5') feet long.
Brown Steering Column Grommet
p/n: 40-0144-89
Grommet, steering column to toe board. Brown rubber. For black see our #40-0144-36. Two and three fourths (2-3/4) inch by seven and one half (7-1/2) inch.
Rumble Seat Step Pad
p/n: 40-0055-44
Pad, rumble seat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.
Rumble Seat Step Pad
p/n: 40-0353-44
Pad, rumble seat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0107-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Accelerator Pedal Service - Brown
p/n: 40-0201-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #40-0201-40.
Front Suspension Bumpers
p/n: 40-0251-32
This Front Suspension Bumper pair for the upper arm is made from high-quality EPDM dense rubber for a precise, factory like fit. Two (2) required per car.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0121-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Front Bumper Grommet
p/n: 40-0122-30
Grommets, front bumper. Hollow construction for good fit. Fully molded rubber.
Trunk Weatherstrip
p/n: 70-1129-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Door Bottom Weatherstrips
p/n: 40-0538-73
This Door Bottom Weatherstrip pair is designed from the original part for superior fitment and seal. Held to door by steel strip. Sponge type rubber as original. For four (4) door models.
License Light Mounting Pad
p/n: 70-3611-17
Pad, rear license light mounting. Replaces factory #902601.
Windshield Stanchion Base Pad
p/n: 40-0079-52
Pads, windshield stanchion mounting. Perfect copy, including concave bottom face to properly fit cowl, right and left.Length: 3.125 inches.
Headlight Bracket Pad
p/n: 40-0236-14
Pad, headlight bracket seal. Without metal core. One (1) pair per car.Length: 5.75 inches.
Swing-Out Windshield Weatherstrip
p/n: 40-0036-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Trunk Weatherstrip
p/n: 70-1691-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Quarter window weatherstrip
p/n: 70-3042-77
Weatherstrip, rear stationary quarter window. Seals around entire permimeter of rear stationary quarter window and rear door window area.
Swing-Out Windshield Weatherstrip
p/n: 70-0057-52
This Swing-Out Windshield Weatherstrip is designed from the original part for superior fitment, finish and sealing function. This windshield weatherstrip is common for most Chrysler models. May also be found in DeSoto, Dodge and Plymouth models. Also used in Packard and Studebaker models.
Vent Window Weatherstrip
p/n: 40-0502-57
This Vent Window Weatherstrip is a cushion for under the vent window frames. Measures 4.375 inches in Length. Sold as a pair.
Accelerator Pedal Pad Service - Black
p/n: 40-0201-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our #40-0201-89.
Swing-Out Windshield Weatherstrip
p/n: 40-0329-50
This Swing-Out Windshield Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts into the metal channel attached to the glass and creates a seal when the glass is pressed against the body of the vehicle.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.