Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Headlight Bucket to Fender Seals
p/n: 70-3085-14
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Hood To Cowl Weatherstrip
p/n: 70-2130-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1252-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Five sixteenths (5/16") of an inch high.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1251-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. One fourth (1/4") of an inch high.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Quarter Window Bumper
p/n: 70-1583-62
Bumper, quarter window stop on sash channel.Length: .8125 inches. Width: .75 inches. Height: .50 inches.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Rear View Mirror Mounting Pad
p/n: 70-3083-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Run Channel Upper Bumper
p/n: 70-0779-62
This run channel upper bumper is manufactured as original with a brass metal core and molded for a precise, factory fit. The seal is installed at the top of the front door vent window frame on the division post.