Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Hood rest pad
p/n: 70-0139-42
Pad, hood rest (hood bumper). In years 1941-47 purchase six (6) per car. In year 1948-1949 purchase two (2) per car.
Hood to Cowl Weatherstrip
p/n: 70-1209-42
Weatherstrip, hood to cowl. To facilitate manufacturing, some may be made in two sections.
License Light Mounting Pad
p/n: 70-0559-17
Pad, license light bracket or base mounting. Two (2) per car.
License Plate Light Lens Gaskets
p/n: 70-0560-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Rear Leaf Spring & Shackle Bushing
p/n: 70-0182-32
This Rear Leaf Spring Bushing is designed from the original part for superior fitment and function. Bushing is for the rear leaf spring front or rear spring to shackle. Two bushings pushed together form one complete bushing. May require eight (8) or twelve (12) each depending or vehicle model if replacing all bushings.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Shift Lever Bushing
p/n: 70-2026-26
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Shock Absorber Bushing
p/n: 70-0545-33
Bushing, rear shock absorber link, upper and lower end. Seven eighths (7/8) inch outside diameter, nine sixteenths (9/16) inch inside diameter, thirteen sixteenths (13/16) inch long. Four (4) per car.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Taillight Mounting Pad
p/n: 70-0471-15
Pads, taillight body to fender, right and left. Also order #70-0658-15 for the taillight lens gasket, and for the taillight gasket order #70-0900-15.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Trunk Weatherstrip
p/n: 70-0872-84
This Trunk Weatherstrip set is designed from original parts for superior fitment and seal. The seals mount directly to the body and cover the full perimeter of the trunk.
Vent division bar weatherstrip
p/n: 50-0317-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Windshield Gasket
p/n: 70-0522-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.