Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
2-3/8" Firewall Grommet
p/n: 30-0056-21
This Firewall Grommet is made to run the ignition cable and thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Taillight Mounting Pad
p/n: 30-0132-15
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Headlight Mounting Pad
p/n: 30-0133-14
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Rear Bumper Grommet
p/n: 30-0137-29
Grommets, rear bumper support bar to body. Fully molded rubber w/ retaining flange.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Side Mount Grommet
p/n: 30-0135-37
Grommets, sidemount carrier arm through fender. Reversible for right and left hand.Height: 4.0 inches.
Steering Column Grommet
p/n: 30-0160-36
Grommet, steering column to toe board. One and five eighths (1-5/8) inch hole for column. Similar to, but larger than our #30-0046-36. Length: 5.25 inches.
Front Fender Seal
p/n: 30-0264-44
Liner, front fender to running board. Reversible right and left replacement. Length: 15.50 inches.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Front Bumper Grommet
p/n: 30-0136-28
Grommets, front bumper support bar to body. Fully molded rubber.
Axle Rebound Pad
p/n: 30-0043-32
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Axle Rebound Pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Engine Mount Service – Revulcanization Only
p/n: 30-0543-11
This Revulcanization Service Only is designed to restore your Engine Mount Stabilizer Bracket to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Weatherstrip Channel
p/n: 30-0020-52
This Windshield Weatherstrip Channel is made of a high-quality EPDM dense rubber extrusion. The channel seals the windshield glass to the body and protects interior of the vehicle.