Vent Division Bar Weatherstrip
p/n: 60-0509-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Antenna Boot
p/n: 70-0212-21
This Antenna Boot is designed from the original part for superior fitment and function. This boot fits at the vehicle running board antenna wire connection.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Trunk Hinge Mounting Pads
p/n: 70-1230-87
This four (4) piece Trunk Hinge Mounting Pad is designed from the original part for superior fitment and function. The installed length is 5-1/2" inches.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.