Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Lock Cylinder Gasket
p/n: 30-0022-71
Pads, door handle escutcheon.Width: 1.875 inches. Height: 1.375 inches.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0016-77
This full swing type Rear Quarter Vent Window Weatherstrip pair is designed from the original part for superior fitment and seal.
Rear Window Gasket Set
p/n: 30-0289-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Running Board Mounting Pad
p/n: 30-0405-48
Insulator, washer, running board to frame bracket bolt, lower. Ten (10) to fourteen (14) required per car.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spring Shackle Bushing
p/n: 30-0420-32
This Spring Shackle Bushing is designed from the original part for superior fitment and function. Six (6) per car. Packard's "self flanging" type.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Stabilizer Grommet
p/n: 30-0406-33
Pad, stabilizer link assembly, front, in upper end at link. Four (4) used per car. Fully molded rubber. One inch (1") outside diameter by three sixteenths inch (3/16") inside hole diameter by three fourths inch (3/4") height.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Taillight Mounting Pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting. Length: 7.125 inches.
Transmission Mount Service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Vent Window Division Bar Weatherstrips
p/n: 70-2094-56
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar vent window glass closes against it. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Windshield Division Bar Gasket
p/n: 30-0146-52
Gasket, windshield division bar. Molded inner and outer, fully detailed.Length: 13.625 inches.
Windshield Gasket
p/n: 30-0281-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.