Front Fender Seal
p/n: 30-0189-44
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Headlight Mounting Pad
p/n: 30-0134-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Headlight Mounting Pad
p/n: 30-0133-14
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Hood Corner Pad
p/n: 30-0130-42
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Hood to Cowl Weatherstrip
p/n: 30-0138-42
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Rear Window Gasket
p/n: 30-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Spare Wheel Mounting Pad
p/n: 30-0446-37
Pad, spare tire inner.Length: .875 inches. Width: .75 inches.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Stabilizer Bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber.
Suspension Bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Taillight Lens Gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Taillight Mounting Pad
p/n: 30-0132-15
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Windshield Gasket
p/n: 30-0477-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket Weatherstrip
p/n: 30-0014-52
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Wiper Transmission Gasket
p/n: 50-0081-53
Gasket, windshield wiper transmission.Width: 2.5625 inches. Height: .8125 inches.