Glass Weatherstrip Kit
p/n: 90-3073-90
This twenty two (22) piece Glass Weatherstrip Kit includes the weatherstrip components needed for the glass on your restoration project. These parts are designed from originals for superior performance and factory fit.
Body Weatherstrip Kit
p/n: 90-3099-90
This six (6) piece Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for your restoration project. These parts are designed from originals for superior performance and factory fit.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Windshield Gasket
p/n: 70-1875-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 50-0215-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Set
p/n: 90-0418-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Steering Column Floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Axle Rebound Pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0081-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mount Service – Revulcanization Only
p/n: 50-0274-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door Weatherstrips
p/n: 50-0533-72
This Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Push-on pin type door weatherstrips mount directly to the doors to seal against the full door perimeter to the vehicle body.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Trunk Emblem Mounting Pad
p/n: 50-0122-17
Mounting pad set, Trunk ornament. Three (3) piece set to replace original twenty six (26) inch single type, perfect fit.Width: 26.0 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Trunk Weatherstrip
p/n: 50-0483-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Brake and Clutch Pedal Pads
p/n: 70-3148-22
Pad, brake and clutch pedal. For vehicles with manual transmission.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Vent division bar weatherstrip
p/n: 60-0534-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.
Parking Brake Pedal Pad
p/n: 50-0405-22
Pad, parking brake pedal. With "PARK" written on pad. Black only. For pedal pad without "PARK" written on pad see our #50-0348-22.Width: 2.0625 inches.
Door Handle Gasket Set
p/n: 70-2673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Headlight Outer Rim Seal
p/n: 27-0063-14
Headlight Outer Rim Seal - Used to seal the headlight beam retainer ring. Replaces # 5945844.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
1-5/8" Firewall Grommet
p/n: 70-2063-20
This Firewall Grommet is used to run the speedometer cable line through the firewall. Designed from original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 70-2062-20
This Firewall Grommet is used to run the oil pressure and temperature line through the firewall. Designed from original parts for excellent workmanship
1-5/8" Firewall Grommet
p/n: 70-2064-20
This Firewall Grommet is used to run the vacuum hose and ignition resistor wire through the firewall. Designed from the original part for excellent workmanship.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
1-3/8" Parking Brake Grommet
p/n: 50-0555-20
This Parking Brake Grommet is used to run the parking brake cable through the frame. Designed from original part for excellent workmanship.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM, Mopar and Packard vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
1-3/16" Utility Plug
p/n: 35-0099-20
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1" Floor Pan Grommet
p/n: 35-0515-20
This Floor Pan Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Firewall Retainer
p/n: 60-0586-20
This Firewall Retainer is used on the firewall insulation panel. Designed from original for the "Christmas Tree" style popular during this time.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
23/32" Firewall Grommet
p/n: 32-0365-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as the vent control cable.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
3/4" Body Hole Plug
p/n: 35-0369-20
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. Designed for shroud or cowl upper panel gauge holes and for various body holes requiring a plug.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
5/8" Wiring Grommet
p/n: 32-0366-53
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the windshield wiper control cable or gas gauge wire through the rear compartment pan.
Clip Fastener - Door Weatherstrip
p/n: 60-0260-73
This Clip Fastener for Door Weatherstrips is made for a precise, factory like fit. Two (2) prong clip fastener with oval screw hole, made with spring steel and cadmium plated. Width: 7/8" inches. Height: 15/16 inches.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
Door Weatherstrip Fastener
p/n: 50-0198-73
This Door Weatherstrip Fastener is steel with a black finish. Each push-in fastener measures one half (1/2") inch long with a thirteen thirty second (13/32") inch diameter head. Reproduction fastener is designed from the original part to fit correctly.
Hood Weatherstrip Retainer
p/n: 70-0564-42
Fastener, hood to cowl weatherstrip (and other uses), self-retaining button head retainer.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
13/16" Firewall Grommet
p/n: 32-0158-17
This Firewall Grommet is designed from the original part for superior fitment and seal. Designed for firewall applications such as running the hand brake cable through the firewall or the license light through the trunk.