Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Lock Cylinder Gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Parking Light Lens Gasket
p/n: 70-1081-16
Gasket, fog and parking light lens housing.Length: 8.5 inches. Width: 4.0 inches.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Rear Bumper To Body Filler
p/n: 70-3078-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Rear Window Gasket
p/n: 70-0699-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Steering Column Finish Strip
p/n: 70-1031-88
Seal, steering column to instrument panel. Extruded rubber twelve (12) inch strip to exact cross-section.Length: 10.5 inches. Width: .50 inches.
Steering Column Floorplate
p/n: 70-1425-88
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Taillight Gasket Set
p/n: 70-0876-15
This eight (8) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. The set includes steel rule die-cut and molded rubber gaskets for the taillight lens and body mounting to fender.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Trunk Weatherstrip
p/n: 70-0896-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Vent Window Division Bar Weatherstrip
p/n: 70-0703-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Windshield Gasket
p/n: 70-0677-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.