Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit, finish and appearance.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Fuel Filler Neck Grommet
p/n: 60-0434-41
This Fuel Filler Neck Grommet is the inner grommet through the quarter panel inside fuel filler door. Fully molded rubber with retaining flange as original for good seal. Three and one eighth inch (3-1/8") outside diameter by two and one eighth inch (2-1/8") inside diameter.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Bumper Support Bar Pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent Window Division Post Weatherstrips
p/n: 60-0596-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
License Plate Light Mounting Pads
p/n: 60-0174-17
This rear License Plate Light Mounting Pad pair is designed from the original part for superior fitment and function. This reproduction mounting pad fits between the rear License Plate Light Housing or Bezel and the vehicle body. Two (2) required per vehicle.
Hood To Cowl Weatherstrips
p/n: 60-0428-42
This Hood To Cowl Weatherstrip pair is designed from original parts so it fits correctly. The pair comes ready to install with pre-punched holes.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Exhaust System Support Pad
p/n: 60-0319-13
This Exhaust System Support Pad is the right-angle type insulator and fabric reinforced. Molded with a steel core at one end as original style.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Steering Column Floorplate Gasket
p/n: 60-0395-36
This Steering Column Floorplate Gasket is designed from the original part for superior fitment and seal. Cover (grommet), steering gear-to-toe board seal. Width: 5-13/16" inches. Height: 6" inches.
Convertible Top Rest Block
p/n: 60-0415-67
Bumper, folding top rear bow (in top compartment). Two (2) required per car. Brass core as original.
Taillight Mounting Pad
p/n: 60-0176-15
Pad, taillight body mounting. Three (3) inch by six and one half (6-1/2) inch overall. Proper lip design.Length: 6.50 inches. Width: 3.0 inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Door Weatherstrip
p/n: 60-0324-73
Weatherstrip, front door opening. Right and left, hinge pillar at beltline. Constructed of soft rubber.Length: 12.0 inches.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Engine Mount Service – Revulcanization Only
p/n: 60-0225-11
This Revulcanization Service Only is designed to restore your Side Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Windshield Gasket
p/n: 70-1791-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends.
Rear Spring Bumper Service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Trunk Weatherstrip
p/n: 70-0870-84
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Hinge Pillar Weatherstrip
p/n: 60-0084-63
This Hinge Pillar Weatherstrip attached to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Door Weatherstrip
p/n: 60-0250-73
Weatherstrip, door bottom and corners, molded right and left. Overall length forty and three fourths (40-3/4) inch per door.
Windshield Gasket
p/n: 60-0194-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0038-55
This Front Door Vent Window Weatherstrips contain the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Front Bow Weatherstrip
p/n: 60-0290-64
Weatherstrip for windshield header, lower or rear, to folding top front roof bow. Installs on the windshield frame. Length: 50-1/4 inches.
Front Door Weatherstrip Set
p/n: 90-0113-72
This seven (7) piece Front Door Weatherstrip Set is the primary seal for the doors to the body. The set includes the door bottom weatherstrip with molded corners, hinge pillar bellows, front edge seals, and rear edge seals.
Front Door Vent Window Set
p/n: 90-0382-90
This six (6) piece Front Door Vent Window Set contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Convertible Roof Rail Weatherstrip
p/n: 60-0076-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Body Weatherstrip Kit
p/n: 90-3506-90
This twenty-three (23) piece Body Weatherstrip Kit includes the major weatherstrip components needed for the body of your classic convertible model. We’ve put everything together in one simple and convenient kit.