Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Trunk Emblem Gasket
p/n: 70-3479-87
This single Trunk Emblem gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) trunk / decklid emblem mounting.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Junction Block Gasket
p/n: 50-0447-15
Gasket, junction block for taillight wiring. One (1) pair used per car.Width: 2.625 inches.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
1-1/16" Trunk Weatherstrip
p/n: 70-0650-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Side Window Header Channel
p/n: 70-0306-58
Plush lined rubber channel for across top of doors above side windows on closed bodies. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.