2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Body Mounting Pad
p/n: 50-0231-48
Shim, body sill. Fully molded rectangular rubber. A total of six (6) are needed per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
1-1/2" Firewall Grommet
p/n: 50-0299-20
This Firewall Grommet is used to run the oil pressure and water temperature lines through the firewall. Designed from original part for excellent workmanship.
Wiper Transmission Gasket
p/n: 70-1197-53
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.