Engine Mount Service – Revulcanization Only
p/n: 40-0410-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
Fender Skirt Edge Weatherstrip
p/n: 40-0279-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Front Bumper Grommet
p/n: 40-0057-30
Grommets, front bumper. Fully molded rubber, inside hole slightly rectangular.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Gearshift Floorplate
p/n: 40-0101-88
Floorplate, gearshift. Black rubber. For brown see our #40-0101-89. Made without rubber boot, but with metal core.
Glovebox Door Bumper
p/n: 40-0501-88
This Glovebox Door Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Handbrake Floorplate
p/n: 40-0102-24
Floorplate, handbrake. Black rubber. For brown see our #40-0102-89. Brass core, proper beading. Bend at assembly.Length: 8.125 inches.
Headlight Mounting Pad
p/n: 40-0277-14
Pad, headlight bracket to radiator shell or side of shroud. (There are several types of these pads used in 1937).
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood Support Rod Top Cap
p/n: 40-0103-42
Top cap, hood support rod. For seven sixteenths (7/16) inch diameter rod. Also see our #40-0346-42.Length: 1.0 inches.
License Light Mounting Pad
p/n: 40-0174-17
Pad, license light mounting. Plain type without edge bead as original.Length: 8.0 inches. Width: 3.25 inches.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.