Outer Beltline Weatherstrip
p/n: 50-0548-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Radiator Bracket Cushion
p/n: 70-2229-31
Radiator support bracket, insulator, lower. Two (2) used per car.Length: 4.5 inches.
Radiator Bracket Cushion
p/n: 70-2014-31
Radiator support bracket, insulator, upper. Two (2) used per car.Length: 6.0 inches.
Rear Door Weatherstrips
p/n: 70-4741-72
These primary Rear Door Weatherstrips mount (pin) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed. Includes 32 sockets for easy installation.
Rear Stationary Side Window Weatherstrips
p/n: 70-3606-77
This Rear Stationary Side Window Weatherstrip pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the rear stationary glass for a precise, factory fit. For stationary windows only.
Rear Window Gasket Set
p/n: 70-3605-81
This Rear Window Gasket Set mounts around the two (2) smaller windows on each side of the back glass on the liftgate. They are molded as left and right with properly shaped corners for a precise, factory fit.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Taillight Lens and Housing Gaskets
p/n: 70-4912-15
This Taillight Lens and Housing Gasket set is designed from the original part for superior fitment and seal. Includes gaskets for Lens to Housing (2) and Housing to Body (2).
Transmission Mount Service
p/n: 50-0463-25
Mount, transmission support. One (1) per car. Revulcanization service only.Length: 5.25 inches. Width: 2.25 inches.
Vent Window Division Bar Weatherstrips
p/n: 50-0337-56
This Front Vent Division Bar Weatherstrip pair is fully molded with a metal core and attaching tabs. This piece mounts on the vertical division bar and seals as the vent glass closes against it.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Window Sash Steel Channels
p/n: 50-0553-59
This rear door Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Twenty-five and one half (25-1/2) inches long.
Window Sash Steel Channels
p/n: 50-0552-59
This Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Twenty (20) inches long.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Windshield Gasket
p/n: 50-0291-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.