Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Rear Bumper Grommet
p/n: 40-0180-30
Grommet, rear bumper support bar to gas tank apron. One and three fourths (1-3/4) inch inside diameter.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Running Board Matting
p/n: 40-0212-49
This Running Board Matting is designed from the original part for superior fitment and a factory like appearance. This four (4) piece set consists of one (1) pair of our #40-0151-49 mats plus two (2) extension pieces to give correct fit for the longer Model CT model running boards.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Cover Pad
p/n: 40-0314-37
Anti-rattle, spare wheel cover in fenderwell.Width: .25 inches.
Swing-Out Windshield Weatherstrip
p/n: 70-0057-52
This Swing-Out Windshield Weatherstrip is designed from the original part for superior fitment, finish and sealing function. This windshield weatherstrip is common for most Chrysler models. May also be found in DeSoto, Dodge and Plymouth models. Also used in Packard and Studebaker models.
Taillight Mounting Pad
p/n: 40-0061-15
Pad, taillight mounting. Chrysler 1932-33 Pad, taillight mounting. Chrysler and other WPC cars. Chrysler 1932-33 Pad, rumble seat step mounting.
Vacuum Clutch Cylinder Boot
p/n: 40-0084-24
Boot, automatic clutch vacuum cylinder rod.Length: 4.0 inches.
Windshield filler
p/n: 40-0318-52
Seal, windshield outer trim. Four (4) piece set for top and bottom of division post trim and for right and left lower corners of windshield panels.
Windshield Filler
p/n: 40-0266-52
Bumpers, windshield frame to pillar. Closed bodies with split windshield. 2 rights and 2 lefts required per car. Four (4) piece set.Length: 2.25 inches.
Windshield Gasket
p/n: 40-0320-52
This Windshield Gasket comes in a four (4) foot strip and is for the lower glass frame to cowl. This weatherstrip is for 2 piece windshields.