Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Hood to Cowl Weatherstrip
p/n: 70-3146-42
This three (3) piece Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip set installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Trunk Or Hatchback Weatherstrip
p/n: 82-0038-84
This Trunk Or Hatchback Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk or hatchback opening directly to the body.
U Jamb Lock Pillar Filler
p/n: 82-0075-79
This U Jamb Lock Pillar Filler seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Division bar chrome retainer
p/n: 70-3226-51
Retainer (rubber), outer windshield, stainless center post molding. Use with original stainless molding and clips.
Hood To Cowl Weatherstrip
p/n: 70-1751-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. A reproduction using a sponge rubber extrusion and fastener clips.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Fuel Neck Grommet
p/n: 70-2522-39
Grommet, fuel filler neck. Correct design with proper shape and form. Two and eleven sixteenths inch (2-11/16") outside diameter by two inches (2") inside hole diameter by one half inch (1/2") height.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Side Window Vertical Leading Edge
p/n: 82-0019-80
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.