Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Taillight Mounting Pad
p/n: 70-1212-15
Pads, taillight mounting. Compound curved right and left hand custom molded pads. Also order the special design weatherproof gaskets for the lenses our #70-1213-15.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Trunk Weatherstrip
p/n: 70-0988-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent division bar weatherstrip
p/n: 70-0694-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Windshield Gasket
p/n: 50-0175-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.