Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Vent division bar weatherstrip
p/n: 70-0783-74
Division bar seal. Made with metal core and attaching tabs like original. Rear door on models with rear door vent.
Taillight to Body Weatherstrips
p/n: 70-0701-15
This Taillight To Body Weatherstrip pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Twenty-three and three fourths (23-3/4) inches developed length.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Hood Corner Pad
p/n: 70-0914-42
Pad, hood corner. Molded left and right like original.Width: 1.375 inches.
Fuel Neck Grommet
p/n: 70-0404-39
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Side Window Vertical Leading Edge
p/n: 70-1271-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear Bumper To Body Filler
p/n: 70-3079-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Cowl Vent Gasket
p/n: 70-0194-54
Gasket, cowl vent. Original solid rubber configuration, not a sponge substitute.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Rear Door Pillar Filler
p/n: 70-0837-79
This Rear Door Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a door jamb seal.
Front Bumper To Radiator Filler
p/n: 70-2777-45
This single piece Front Bumper To Radiator Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions.
Rear Bumper To Body Filler
p/n: 70-3078-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Fuel Neck Grommet
p/n: 70-0050-39
Grommet, fuel filler neck. Fully duplicates original with large retaining flange. Flexible, molded rubber. Four and one eighth inch (4-1/8") outside diameter by two and three sixteenth inch (2-3/16") inside hole diameter.
Front and Rear Bumper Spacer
p/n: 70-0184-30
Spacer or mute, front and rear bumper mounting bar to gravel deflector. Fully molded rubber. Two and nine sixteenths inch (2-9/16") outside length by seven eighths inch (7/8") width by thirteen sixteenths inch (13/16") height.
Fuel Neck Grommet
p/n: 50-0067-39
Grommet, fuel filler neck. Oblong fully molded rubber. Two and one eighths inch (2-1/8") inch inside length by three and one half inch (3-1/2") outside diameter by three and three fourths inch (3-3/4") outside length.
Window Felt Outer Beltline Weatherstrips - Front Door Only
p/n: 80-1019-57
This is a high-quality material style Window Felt Outer Beltline Weatherstrip pair. This ready to install two (2) piece beltline pair includes Only the Outer window felts (the part sealing the outside of the vehicle) for the front door side windows.
Brown seat back rest pad
p/n: 70-0482-89
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Rear Valance Gasket Strip
p/n: 70-0461-45
This Rear Valance Gasket Strip installs on the gravel shield to body. Designed from the original part so it fits correctly. Customer will need to cut bolt clearance as needed.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Side mount cover pad
p/n: 70-0787-37
Pad, channel type, sidemount cover. Six (6) piece set. Two (2) 11.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Door weatherstrip
p/n: 70-0525-73
Weatherstrip, rear door hinge pillar at beltline Two (2) per car. Two (2) piece set.
Side Window Vertical Leading Edge
p/n: 70-0831-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 70-0795-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Outer Beltline Weatherstrip
p/n: 70-0784-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Upper Lock Pillar Weatherstrips
p/n: 70-1762-73
This Upper Lock Pillar Weatherstrip pair is designed from the original part for superior fitment and seal. These auxillary door weatherstrips fit to the lock pillar vertical.
Rumble Seat Step Mounting Pad
p/n: 70-0262-45
Pad, rumble seat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Beltline Weatherstrip
p/n: 70-0749-60
This Beltline Weatherstrip is sold as a three (3) foot pair. Rigid, flocked rubber lip, with flat stainless bead. Available in 3ft pair.
Headlight Mounting Pad
p/n: 70-0256-21
Mounting pad, horn and headlight brace rod to fender. One and one half (1-1/2) inches by three and one eighth (3-1/8) inches outside diameter.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
2-13/16" Firewall Grommet
p/n: 70-0644-20
This Firewall Grommet is used to run dash wires through the firewall. Designed from the original part for superior fit and seal.
Fog light lens gasket
p/n: 70-2547-17
Gasket, fog light lens to reflector. Machine die cut. For models with factory fog lights.
2-13/16" Firewall Grommet
p/n: 70-0447-20
This Firewall Grommet is designed to be used for the main wiring harness and miscellaneous wires through the firewall. (The main cable and up to eight (8) other wires, tubes or cables.)
Side Window Vertical Leading Edge Weatherstrips
p/n: 70-0904-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Headlight Mounting Pad
p/n: 70-0257-14
Mounting pads, horn and headlight stanchion. Two and one half (2-1/2) inches by five (5) inches outside diameter.Length: 5.0 inches. Width: 2.5 inches.
Rigid Run Channel
p/n: 70-0752-58
Sliding glass window unbeaded u-channel secures sliding glass and eliminates rattle. Available in 6ft lengths.
2-7/8" Firewall Grommet
p/n: 70-1747-20
This Firewall Grommet is used to pass the dash wires through the firewall. Designed from the original part for superior fit and seal.
Battery Cable Grommet
p/n: 70-2318-20
Grommet, battery cable through radiator shroud. Reproduction of original rectangular design exactly. Replaces #1469080. Length: 2.4375 inches. Width: 1.5 inches.
Run Channel Upper Bumper
p/n: 70-1044-62
This run channel upper bumper is manufactured as original with brass metal core.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0344-80
This Side Window Vertical Leading Edge Weatherstrips pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Leaf Spring to Shackle Bushings
p/n: 70-3344-35
This Leaf Spring To Shackle Bushing set is designed from the original part for superior fitment and function. This bushing installs into the leaf spring eye to fit between the rear shackle to leaf spring. This is a four (4) piece set for both rear leaf springs.
Upper Lock Pillar Filler
p/n: 70-0782-79
A fully molded Upper Lock Pillar Filler pair. One and five eighths inch (1-5/8") wide and two- and three-quarter inches (2-3/4") high. This part seals the bottom of the rear side window and may also be known as a door jamb seal.
Hood to Cowl Weatherstrip
p/n: 70-1253-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay directly to the body. Seventy-two (72") inches OAL and includes fifteen (15) 70-1255-42 plastic clips for installation.
Rear Bumper to Body Filler
p/n: 70-3164-45
This Rear Bumper To Body Filler pair is designed from the original part for superior fitment and function. Two (2) filler pieces are die cut from quality masticated rubber to authentic original dimensions. These pieces fit between the rear bumper and the vehicle body.
Side Window Vertical Leading Edge Weatherstrips
p/n: 50-0427-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear Door Lock Pillar Fillers
p/n: 70-1816-79
This Rear Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear door window. Fully molded authentic rubber construction.
Vent division bar weatherstrip
p/n: 70-1091-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 70-0781-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Bumper End Filler Set
p/n: 70-3769-30
This four (4) piece Rear Bumper End Filler set is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Side Window Leading Edge
p/n: 70-1090-80
This Side Window Leading Edge attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Made of a top-quality EPDM dense rubber.
Vent division bar weatherstrip
p/n: 60-0682-56
Vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. Note: used for front door vent on 1958 Chevrolet and Pontiac li
Vent division bar weatherstrip
p/n: 70-1046-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Division Bar Weatherstrip
p/n: 70-0924-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.