Hood Corner Pad
p/n: 40-0089-42
Pads, hood front corners. Rubber with metal core as original.Length: 1.4375 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood to Cowl Weatherstrip
p/n: 70-2236-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-2341-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. A proper extrusion approximately sixty-two (62) inches long with pre-installed fastener clips.
Hood to Cowl Weatherstrip
p/n: 70-2219-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) long original profile extrusion provides complete coverage.
Hood to Cowl Weatherstrip
p/n: 40-0470-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) foot long x 13/16” wide weatherstrip provides complete coverage.
Hood to Cowl Weatherstrip
p/n: 40-0475-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip can also be used as a radiator seal. Available by the foot.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 40-0503-42
Bumper, hood to fender ledge. Correct original cross-section. Up to ten (10) required per car.
Hood to Fender Bumper Set
p/n: 70-2672-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper Set
p/n: 70-2315-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Radiator Weatherstrip
p/n: 70-2385-43
Weatherstrip, hood to radiator. Proper rubber cross section with pre-drilled holes, cut outs and included attaching clips.Length: 61.25 inches.
Hood to Radiator Weatherstrip
p/n: 70-2386-43
Weatherstrip, hood to radiator. Proper rubber cross section with pre-drilled holes, cut outs and included attaching clips.Length: 62.875 inches.
Hood to Radiator Weatherstrip
p/n: 70-1580-42
Weatherstrip, hood to radiator shroud.Width: 1.3125 inches.
Hood to Radiator Weatherstrip
p/n: 40-0512-42
Weatherstrip, hood to grill or radiator shroud. Two (2) pieces, each sixteen (16) inches.Width: 1.3125 inches.
Hood to Radiator Weatherstrip
p/n: 70-2073-42
This Hood to Radiator weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the front of the engine bay directly to the radiator support.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.