Headlight Mounting Pad
p/n: 40-0159-14
Pad, headlight mounting. Made with small weatherlip around edge.Length: 5.6875 inches. Width: 2.875 inches.
Headlight Mounting Pad
p/n: 40-0277-14
Pad, headlight bracket to radiator shell or side of shroud. (There are several types of these pads used in 1937).
Heat and Sound Insulator Underlayment Set
p/n: 70-4672-88
This four (4) piece die-cut Heat and Sound Insulator Underlayment Set lays under the carpet. This underlayment will decrease road noise and decrease heat inside the interior compartment. Pre-cut and ready to be installed into your vehicle to improve driving comfort.
Hinge Pillar Weatherstrip
p/n: 70-1811-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Pillar Weatherstrip
p/n: 70-1423-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Pillar Weatherstrips
p/n: 70-1929-63
Convertible Hinge Pillar Weatherstrips - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Post Weatherstrip
p/n: 70-1769-73
Weatherstrip, body hinge pillar, lower (front door).Length: 10.125 inches.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Hood Bumper
p/n: 70-1608-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
Hood Bumper
p/n: 82-0212-42
Bumper, hood to fender ledge. Excellent reproduction, made just like original.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood Support Rod Top Cap
p/n: 40-0103-42
Top cap, hood support rod. For seven sixteenths (7/16) inch diameter rod. Also see our #40-0346-42.Length: 1.0 inches.
Hood to Cowl Weatherstrip
p/n: 70-3902-43
This Hood To Cowl Weatherstrip is approximately sixty-five (65) inches long. This part is designed from originals for a superior performance and a factory fitment to your vehicle.
Hood To Cowl Weatherstrip
p/n: 70-2391-43
This Hood To Cowl Weatherstrip is designed from the original part. Proper rubber cross section with pre-inserted attaching clips. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-2236-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-2390-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Made of a dense rubber extrusion and pre-installed fastener clips.
Hood to Cowl Weatherstrip
p/n: 70-1640-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This 38-1/2” long x 11/16” wide weatherstrip provides complete coverage.
Hood to Cowl Weatherstrip
p/n: 70-2388-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Proper rubber cross section extrusion with pre-installed attaching clips.