Tailgate wedge
p/n: 70-2855-87
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Body Mounting Pad
p/n: 50-0328-48
Pad, body mounting to frame. Fully molded rubber. Up to twenty (20) required per car. Check number needed for your particular body. Two inch (2") square by five eights inch (5/8") inside hole diameter by seven sixteenths inch (7/16") height.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Body Mounting Pad
p/n: 50-0132-48
Pad, body mounting. Fully molded rubber. One and three fourths inch (1 3/4") outside diameter by three eighths inch (3/8") inside hole diameter by five sixteenths inch (5/16") height.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Body Mounting Pad
p/n: 50-0133-48
Pad, body mounting. Fully molded rubber. Two inches (2") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Hood bumper
p/n: 50-0095-42
Bumper, hood to fender ledge. Self retaining type. See our # 50-0194-42 for center type.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
1-5/8" Cowl Hole Grommet
p/n: 70-2065-20
This Firewall Grommet is used to plug the hole on the cowl side of the firewall. Designed from original part for excellent workmanship.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
1-9/16" Firewall Grommet
p/n: 50-0566-20
This Firewall Grommet is used to used to run the water temperature gauge, heater blower wire, or other various wires through the firewall. Designed from the original part for superior fit and seal.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.