Hood Corner Pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Trunk Emblem Mounting Pad
p/n: 50-0113-17
Mounting pad, trunk ornament, excellent material and workmanship.Width: 11.8125 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Brown Steering Floorplate
p/n: 50-0260-89
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Hood bumper
p/n: 50-0326-42
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Upper Division Post Bumpers
p/n: 70-1629-62
These Upper Division Post Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits at the top of the division post(s) on the right and left sides of the vehicle.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Rumble Seat Weatherstrip
p/n: 70-0166-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Hood to Cowl Weatherstrip
p/n: 70-1815-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 50-0561-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. Part is pre-drilled with 12 holes and includes button retainers.
Hinge post weatherstrip
p/n: 70-0383-73
Weatherstrip, hinge post at instrument panel. Steel inserts at holes
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Steering Column Floorplate
p/n: 50-0415-36
Floorplate, steering column. Black rubber. For brown see our #50-0415-89.Length: 4.125 inches. Width: 4.125 inches.
Brown Accelerator Service
p/n: 70-1660-89
Pedal, accelerator. Brown rubber. Revulcanization service only. For black see our #70-1660-40. Color: brown Length: 9.0 inches.
Antenna Mount Service
p/n: 50-0280-21
Mount, antenna, insulator shell assembly, running board. Revulcanization service only. Use in conjunction with our # 50-0305-21.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Convertible Top Arm Pad
p/n: 70-1216-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
U Jamb lock pillar filler
p/n: 50-0307-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Trunk Emblem Mounting Pad
p/n: 50-0185-17
Mounting pad, trunk emblem base, made in three pieces. Customer will have to modify outer holes.Width: 23.0 inches.
Axle Rebound Pad
p/n: 50-0370-35
Bumper, rear axle stop. Molded left and right. Revulcanization service only.
Rear Window Gasket
p/n: 60-0469-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Trunk Weatherstrip
p/n: 50-0483-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Transmission Mounting Pad
p/n: 50-0335-25
Transmission support pad, insulator blocks, upper and lower.
Accelerator Pedal Service
p/n: 70-1660-40
Pedal, accelerator. Black rubber. Revulcanization service only. For brown see our #70-1660-89. Length: 9.0 inches.
Trunk Weatherstrip
p/n: 70-1128-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Trunk Weatherstrip
p/n: 70-0988-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Accelerator Pedal Service
p/n: 50-0414-40
Pedal, accelerator. Revulcanization service only. Includes new rubber sockets for hinges. Length: 9.125 inches.
Roof Rail Filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Molded as left and right with a corrosion resistant brass metal core.
Taillight Mounting Pad
p/n: 50-0173-15
Pad, taillight mounting, right and left.Width: 10.5625 inches.
Taillight Mounting Pad
p/n: 50-0121-15
Mounting pads, taillights, right and left. Width: 10.5625 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Front or Rear Door Weatherstrips
p/n: 82-0150-72
This is a universal push-on type Door Weatherstrip. Made with flexible steel core. Can be used for the front or rear passenger entry doors.
Trunk Emblem Mounting Pad
p/n: 50-0122-17
Mounting pad set, Trunk ornament. Three (3) piece set to replace original twenty six (26) inch single type, perfect fit.Width: 26.0 inches.
Front or Rear Door Seals
p/n: 90-0130-72
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Transmission Mount Service
p/n: 50-0262-25
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Tailgate Weatherstrip
p/n: 70-3424-84
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends.
Trunk Weatherstrip
p/n: 70-0796-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front or Rear Door Weatherstrips
p/n: 90-0128-72
This Front or Rear Door Weatherstrip set is the primary weatherstrips for the door to the body. The set contains two (2) weatherstrips for either the front or the rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Transmission Mount Service
p/n: 50-0263-25
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Rumble Seat Weatherstrip
p/n: 25-0025-85
This Rumble Seat Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Rear Bumper Grommet
p/n: 50-0126-29
Grommets, rear bumper. Hollow construction for good fit. Fully molded rubber with locating tabs.
Trunk Weatherstrip
p/n: 70-0797-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Door Weatherstrip Set
p/n: 90-1822-72
This Door Edge Weatherstrip set is designed from the original parts for superior fitment and seal. These primary door weatherstrips install directly to the left / right front or rear doors to seal the full perimeter of the doors against the vehicle body when the door is closed.
Convertible Front Header Bow Weatherstrip
p/n: 70-0157-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, INNER, right and left.
Rear Window Gasket
p/n: 70-0687-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0433-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.