Run Channel Upper Bumper
p/n: 70-0779-62
This run channel upper bumper is manufactured as original with a brass metal core and molded for a precise, factory fit. The seal is installed at the top of the front door vent window frame on the division post.
Run Channel Upper Bumper
p/n: 70-1044-62
This run channel upper bumper is manufactured as original with brass metal core.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vertical Leading Edge
p/n: 70-1271-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 70-0832-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 60-0633-80
This Side Window Vertical Leading Edge Weatherstrip attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece.
Side Window Vertical Leading Edge
p/n: 60-0644-80
This Side Window Vertical Leading Edge weatherstrip pair attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-3061-45
This comprehensive ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right made pieces fit over suspension a-arms and inside front inner fenders.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Lower Weatherstrip
p/n: 70-2123-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate with properly spaced plastic clips.
Tailgate Weatherstrip
p/n: 70-1519-87
Weatherstrip, tailgate opening. Pinchweld finish on body. This tailgate weatherstrip reproduction is designed from the original part for superior fitment and seal.
Tailgate Weatherstrip Filler
p/n: 70-2056-87
Filler, tailgate weatherstrip at beltline, on body. Fully molded with holes for attaching pins.Length: 4.0 inches.
Taillight Lens Gasket
p/n: 70-1793-15
Gasket, taillight lens. Made of die cut sponge rubber to original configuration.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Track Bar Bushing
p/n: 50-0527-34
Bushing, track bar. Molded out of BUNA rubber with correct metal sleeve like original.Height: 1.875 inches.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Transmission Mount Service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.