Crown Molding Mounting Pad
p/n: 50-0244-44
Mounting pads, rear fender crown molding. Requires two (2) per car.Length: 40.625 inches.
Detachable Center Post Pad
p/n: 70-0273-67
Pads, upper and lower for removable center post, brass carcass as original. Four (4) piece set.Length: 3.125 inches.
Detachable center post pad
p/n: 70-0248-67
Pads, center body removable pillar, Brass core, four (4) piece set.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Detachable Center Post Pad
p/n: 70-0206-67
Bumpers, convertible top detachable pillar, upper and lower, right and left. With metal core per original, four (4) piece set.
Detachable Center Post Pad
p/n: 70-0295-67
Pads, detachable center post, upper and lower, steel core. One and nine sixteenths (1-9/16) inches by four and one fourth (4-1/4) inches. Four (4) piece set.
Detachable Center Post Pad
p/n: 50-0119-67
Pad, detachable center post, top and bottom. Brass core, four (4) piece set.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Directional Signal Light Lens Gaskets
p/n: 70-4043-16
This Directional Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the front Signal Light Lens and the front Signal Light Housing or Bezel.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Door Bottom Drain Hole Seal
p/n: 70-0938-70
This Door Bottom Drain Hole Seal is designed from the original part for superior fitment and seal. This part fits into the lower door on both two (2) and four (4) door models.
Door Bumper
p/n: 33-0505-71
This upper / lower Door Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function. Length: 7/8 inches. Width: 13/16 inches. Height: 1-1/8.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1563-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.