Front Bumper To Hood Filler
p/n: 50-0500-30
This Front Bumper To Hood Filler is designed from the original part for a superior fitment level. This filler piece installs between the front bumper and vehicle body. Correct rubber extrusion cut to sixty (60") inches.
Front Door Vent Window Set
p/n: 90-0318-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 70-1584-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 70-1000-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. This part is the primary door weatherstrip to seal the doors to the body. Push pin installation.
Front Door Weatherstrips
p/n: 50-0475-72
This Front Door Weatherstrip is the primary door to body weatherstrip. Includes fasteners and six (6) clips for easy installation. Made with top quality rubber.
Front Door Weatherstrips
p/n: 82-0051-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Push-on pin type door weatherstrips mount directly to the front doors to seal the perimeter of the doors to the vehicle body when closed. This part is the primary door to body weatherstrip.
Front Door Weatherstrips
p/n: 82-0050-72
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary front door weatherstrips seal the driver (LH) and passenger (RH) doors when closed.
Front Fender Inner Seal Set
p/n: 70-3318-45
This four (4) piece Front Fender Inner Seal set is designed from the original part for superior fitment and function. The seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Front Signal Light Lens Gaskets
p/n: 70-4048-16
This Front Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the front turn signal light lens and the front turn signal light housing or bezel.
Hardtop Roof Rail Over Door Weatherstrips
p/n: 82-0044-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the front side window when the window is fully raised. This part stops at the quarter window, and is only over the front door glass.
Hardtop Roof Rail Weatherstrips
p/n: 70-1588-68
This Hardtop Roof Rail Weatherstrip fits on the roof of the vehicle and seals the side window when the window is fully raised.
Hardtop Roof Rail Weatherstrips
p/n: 82-0047-68
This Hardtop Roof Rail Weatherstrip pair is made of ozone resistant EPDM sponge rubber with molded A pillar ends and corners for a factory like fit. These high-quality weatherstrips fit on the roof of the vehicle and work to seal the side windows when the window is fully raised.
Hardtop Roof Rail Weatherstrips
p/n: 50-0426-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised. Includes two (2) clips.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Hood Bumper
p/n: 50-0511-42
Bumper, hood to fender ledge. Correct detail, made from highest quality rubber.Width: .75 inches. Height: .875 inches.
Hood Bumper Cap
p/n: 70-1651-42
This Hood Bumper Cap is fully molded and designed from the original part for superior fitment and seal. Slip-over style application.
Hood To Cowl Weatherstrip
p/n: 50-0486-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood To Cowl Weatherstrip
p/n: 50-0501-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-1253-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay directly to the body. Seventy-two (72") inches OAL and includes fifteen (15) 70-1255-42 plastic clips for installation.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Parking Light Lens Gaskets
p/n: 70-3073-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Prop shaft support service
p/n: 50-0510-27
Support, propeller shaft, bearing retainer. Revulcanization service only.
Radiator Bracket Cushion
p/n: 70-2070-31
Radiator support bracket, insulator, small type. See our #70-2050-31 for large type.Length: 4.5 inches.
Radiator bracket cushion
p/n: 70-2050-31
Radiator support bracket, insulator, large type. See our #70-2070-31 for small type.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Side Window Leading Edge Weatherstrips
p/n: 50-0428-80
This Side Window Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge
p/n: 70-0759-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side Window Vertical Leading Edge Weatherstrips
p/n: 70-1700-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3062-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2796-45
This three (3) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Taillight Lens Gaskets
p/n: 70-4049-15
This Taillight Lens Gasket pair, for right and left side, is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing.
Taillight Mounting Pad
p/n: 70-2166-15
Pad, taillight mounting to rear quarter panel. Proper extrusion cross section like original. Two (2) strips twenty-four (24) inch long. Length: 24.0 inches.
Trunk Emblem Gasket
p/n: 70-3479-87
This single Trunk Emblem gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) trunk / decklid emblem mounting.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
U Jamb Door Lock Pillar Fillers
p/n: 82-0053-79
This quarter to side window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
U Jamb Lock Pillar Fillers
p/n: 70-1617-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
U Jamb Lock Pillar Fillers
p/n: 70-1573-79
This quarter to side window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Upper Division Post Run Channel Set
p/n: 70-1886-62
This four (4) piece Upper Division Post Run Channel set is designed from the original part for superior fitment and function. This part fits on the division post opposite the vent window to provide a flexible run channel for the side window glass operation.
Vent division bar weatherstrip
p/n: 70-1585-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.