Rear Stabilizer Bushing
p/n: 50-0171-34
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
License Light Mounting Pad
p/n: 50-0046-17
Pad, rear license light, middle of trunk.Width: 16.125 inches.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Outer Beltline Weatherstrip
p/n: 50-0549-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Turn Signal Mounting Pad
p/n: 50-0152-17
Mounting pad, turn signal light, on trunk.Width: 11.75 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Rear Door Lock Pillar Weatherstrips
p/n: 70-1907-79
This Rear Door Lock Pillar Weatherstrip pair seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood Corner Pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Hood Corner Pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
U Jamb Lock Pillar Filler
p/n: 70-1433-79
This U Jamb Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Brown Steering Floorplate
p/n: 50-0260-89
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Hood to Cowl Weatherstrip
p/n: 70-0497-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Beltline Weatherstrip
p/n: 70-2251-60
Weatherstrip, front door window outer scraper seal at beltline. Original type with bright bead attached to seal. Made with proper attaching clips.
Beltline Weatherstrip
p/n: 70-2252-60
Weatherstrip, rear door window outer scraper seal at beltline. Original type with bright bead attached to seal. Made with proper attaching clips.
Liftgate Weatherstrip
p/n: 70-2250-85
This Liftgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate opening directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 70-0289-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Upper Division Post Bumpers
p/n: 70-1629-62
These Upper Division Post Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits at the top of the division post(s) on the right and left sides of the vehicle.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Beltline Weatherstrip
p/n: 70-0961-60
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Rumble Seat Weatherstrip
p/n: 70-0166-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Side window leading edge
p/n: 60-0642-80
Side window vertical leading edge weatherstrip. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece
Hood to Cowl Weatherstrip
p/n: 70-1815-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.