Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Directional & Parking Light Lens Gaskets
p/n: 70-3230-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Hood To Cowl Weatherstrip
p/n: 70-4897-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Shock Absorber Bushing
p/n: 70-0545-33
Bushing, rear shock absorber link, upper and lower end. Seven eighths (7/8) inch outside diameter, nine sixteenths (9/16) inch inside diameter, thirteen sixteenths (13/16) inch long. Four (4) per car.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Rear Stabilizer Bushing
p/n: 70-0905-33
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber.
Rear View Mirror Mounting Pad
p/n: 70-2791-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is one (1) door mounted rear view mirror.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Floor Pan Plug
p/n: 35-0576-45
Plug, floor pan, oval, self-retaining, fits one fourth (1/4) inch by nine sixteenths (9/16) inch hole.
Adjustable Hood Bumper
p/n: 70-2830-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires three (3) per vehicle.
Convertible Top Arm Cover Cap
p/n: 70-0736-67
This four (4) piece Convertible Top Arm Cover Cap set is designed from the original part for superior fitment, finish and function. Installs on the folding pillar to side roof rail links. A perfect copy in original grey rubber. Four (4) piece set.Length: 1-3/4" inches.
Hood Bumper
p/n: 70-0987-42
Bumper assembly, with stud. Two (2) or four (4) used per car as required.Height: 3.25 inches.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Wiper Cowl Weatherstrips
p/n: 70-4882-43
This Wiper Cowl Weatherstrip pair is designed from the original part for superior fitment and seal. This is the rear outer wiper cowl pair. These weatherstrips sit behind the hood to cowl primary weatherstrip by the left-side and right-side hood hinges.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door Bumper
p/n: 70-1158-71
Pad, door jamb, (door side bumper).Length: 1.25 inches. Width: 1.125 inches.
Door Handle Gasket Set
p/n: 70-0572-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Bumper Support Bar Pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Headlight Bucket to Fender Seals
p/n: 70-3085-14
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Door Handle Gasket Set
p/n: 70-1647-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Body / Cowl to Fender Seals
p/n: 70-3075-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Front Auxiliary Wheel House to Inner Fender Seals
p/n: 70-3080-45
This two (2) piece Front Auxiliary Wheel House To Inner Fender Seal pair is designed from the original part for superior fitment and seal. Fender seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Rear View Mirror Mounting Pad
p/n: 70-3082-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Rear View Mirror Mounting Pad
p/n: 70-3081-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Rear View Mirror Mounting Pad
p/n: 70-3083-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Trunk Emblem Gasket
p/n: 70-3220-87
This single Trunk Emblem gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) trunk / decklid emblem mounting.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Adjustable Hood Bumper
p/n: 70-0935-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Rear Leaf Spring & Shackle Bushing
p/n: 70-0182-32
This Rear Leaf Spring Bushing is designed from the original part for superior fitment and function. Bushing is for the rear leaf spring front or rear spring to shackle. Two bushings pushed together form one complete bushing. May require eight (8) or twelve (12) each depending or vehicle model if replacing all bushings.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Taillight Gasket
p/n: 70-0836-15
Gasket, taillight housing and molding-to-tailfin. Seven and one half (7-1/2) foot strip. Enough for both lights.Length: 90.0 inches.
Trunk Lock Emblem Gasket
p/n: 70-0875-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact profile.Width: 1.875 inches. Height: 1.9375 inches.
Trunk Lock Emblem Gasket
p/n: 70-0878-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact dimensions.Width: 2.0 inches. Height: 2.0 inches.
Brake Cable Boots
p/n: 70-0067-24
This Brake Cable Boot pair is designed from the original part for superior fitment and seal. Boot fits over brake cables at front or rear wheels.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Adjustable Hood Bumper
p/n: 70-0973-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. 1957-1958 models use four (4) per vehicle. 1959-1960 models use two (2) per vehicle.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Shift Lever Bushing
p/n: 70-2026-26
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
1-1/16" Trunk Weatherstrip
p/n: 70-0650-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
1-5/16" Firewall Grommet
p/n: 32-1215-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Designed for wire, cable, tubes, etc, in the firewall.
Side Window Header Channel
p/n: 70-0306-58
Plush lined rubber channel for across top of doors above side windows on closed bodies. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
15/16" Trunk Weatherstrip
p/n: 70-0490-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
2-1/4" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Door handle ferrule grommet
p/n: 70-0173-69
Grommet for outside door handle ferrule. Similar to, but not interchangeable with our #70-0009-69.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
7/8" Door Weatherstrip
p/n: 70-0492-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Body Mounting Pad
p/n: 70-0264-48
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Parking Light Grommet
p/n: 70-0679-16
Grommet, parking light. Taillight body for wiring connectors. Hose section not furnished.Height: 1.0 inches.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.