Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Steering Column Grommet
p/n: 70-2316-88
Grommet, steering column at floor. Order our #70-2316-88 seal separately.
Windshield Gasket
p/n: 70-0078-52
This Windshield Gasket is made of a high-quality EPDM dense rubber extrusion. This four (4) foot weatherstrip mounts on the lower windshield.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Side Window Vertical Leading Edge Weatherstrips
p/n: 70-0882-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Carpet Heel Plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Steering Column Collar Grommet
p/n: 70-0682-88
This Steering Column Collar Grommet is designed from the original part for superior fitment and function. The grommet fits the steering column at toe board over carpet.
Accelerator Pedal Pad
p/n: 70-0407-40
Pad, accelerator pedal. Slipover style. Exact copy and top quality rubber.
Convertible Roof Rail Bumper
p/n: 70-1023-67
Bumper, convertible top. Fully molded with threaded metal core. Excellent quality.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Fog light lens gasket
p/n: 70-3106-16
Gasket set, front turn signal and fog light lens. Four (4) piece set.
Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Hood To Cowl Weatherstrip
p/n: 70-3322-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Quarter Window U Jamb Door Lock Pillar Fillers
p/n: 70-0982-79
This Quarter Window U Jamb Door Lock Pillar Filler pair seals the bottom of the rear side window. May also be known as a door jamb seal.
Vent Window Division Post Run Channels
p/n: 70-0985-58
This Vent Window Division Post Run Channels pair installs on the backside of the vent window division post. Flexible run channel is flock lined with a molded-in upper bumper as original.
Headlight seal
p/n: 70-2574-14
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood Corner Pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Hood Corner Pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Front Door Vent Window Upper Stop Bumpers
p/n: 70-4638-62
This Front Door Vent Window Upper Stop Bumper pair is designed from the original part for superior fitment and function. Fits at the top of the front door vent window frame. Fully molded over a brass metal core.
Fuel Neck Grommet
p/n: 50-0059-39
Grommet, fuel filler neck. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2-3/16") inside diameter by three fourths inch (3/4") height.
Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
Door Center Post Weatherstrips
p/n: 70-0847-73
This four (4) piece Door Center Post Weatherstrip set is designed from the original part for superior fitment and seal. A four (4) piece set for the left and right, front and rear doors. Authentic cross-section and construction.
Steering Column Finish Strip
p/n: 70-0719-88
This Steering Column Finish Strip is designed from the original part so it fits correctly.
Headlight Mounting Pad
p/n: 70-0259-14
Mounting pads, headlight bar to radiator shell brace rod (at shell).
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Bow Corner Filler
p/n: 70-0975-67
Filler, front corner of convertible top front bow. Made from soft durable rubber. Includes separate brass retainers.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Trunk Weatherstrip
p/n: 82-0033-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Parking Light Mounting Pad
p/n: 70-0253-16
Pads, parking light to fender mounting.Length: 2.875 inches.
Fuel Neck Grommet
p/n: 25-0015-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Flat bottom has slight ridge (seam) along edge.
Fuel Neck Grommet
p/n: 70-0599-39
Grommet, fuel filler neck, through rear fender splash panel. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2 3/16") inside hole diameter.
Vent Frame Deflector
p/n: 70-1792-62
Deflector, beneath vent frame.Length: 5.75 inches. Width: 1.0 inches.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.